The Trophy Diesel...

[philofab]

Wow. $1200 for used leaf springs?!?!? Ummm, why do springs for this cost more than every other truck on the planet? I am missing something?

[Bondobob]

Carli shackles = $$'s . The Deavers are as usual, His set up has leafs and shackles.

[philofab]

Lol. I wonder if my shackles from my other crew would work... I can't see a reason to spend that much on something so simple.

[philofab]

Philo, A few guys have been revamping trucks on DTX and there's a set of Deaver LT's with Carli shackles in the classifieds.

The crowd is tough on that forum Bob. If it doesn't say Thoren or Carli it doesn't work I guess.

It might take a while for them to warm up to me...

[Smart Alex]

That's what the ones for mine cost new over 5 yrs ago. And also the single best upgrade hands down for the dodge.

[Bondobob]

Philo, A few guys have been revamping trucks on DTX and there's a set of Deaver LT's with Carli shackles in the classifieds.

The crowd is tough on that forum Bob. If it doesn't say Thoren or Carli it doesn't work I guess.

It might take a while for them to warm up to me...

Yeah, and I driveway welded my truss as well as the evil deed of getting some Thuren stuff and mixing in some Carli parts.... I may burst into flames at any minute!

[philofab]

Yeah, and I driveway welded my truss as well as the evil deed of getting some Thuren stuff and mixing in some Carli parts.... I may burst into flames at any minute!

I was reading on there about how the front end needed to be jigged and welded in such a way that you needed to do a bunch of equations to figure out weld warpage and then rent a giant trash can, fill it with kitty litter, and put propane heaters on it to slow cooling.

That's great and all if you are building a satellite out of cast metals for some reason but I doubt he has ever checked how stuff comes out of the factory. Older cars I'd see .500 differences between frames and 9" housing with the ends 3/8 off.

I will be welding my "C"s the same way you did...

[ChaseTruck754]

That's great and all if you are building a satellite out of cast metals for some reason but I doubt he has ever checked how stuff comes out of the factory. Older cars I'd see .500 differences between frames and 9" housing with the ends 3/8 off.

Funny how crazy some people go with stuff, and yes I've noticed the same in factory "tolerances" (if you could even call them that.
These 70's trucks will open your eye for how different stuff could be side to side.

[Tchajagos]

That's great and all if you are building a satellite out of cast metals for some reason but I doubt he has ever checked how stuff comes out of the factory. Older cars I'd see .500 differences between frames and 9" housing with the ends 3/8 off.

It was a different time, a less plastic time.

[Bondobob]

Yeah, when "Digital" was using your fingers....... And the damn Hash tag was a pound sign.....

[Phoenix0783]

Yeah, when "Digital" was using your fingers....... And the damn Hash tag was a pound sign.....

#poundsign

[philofab]

Cheap crappy bedrail covers ripped off from the wind today...

[ChaseTruck754]

Tonneau time!

Is the bed itself sprayed with Line-X or something? If not you gonna spray it & run it up over the bedrails?

[philofab]

The rest of the truck is already linexed. Not sure yet if I am going to have them do the bed rails or just but a quality cap set...

[D1cker1]

Snugtop camper

[philofab]

No camper shell.

[philofab]

ImageUploadedByTapatalk1388973182.612249.jpg (71.9 KiB) Viewed 1198 times

Interior lights were lacking, so I added a few feet of flexible PCB LED rope.

[hobbyturnedobsession]

Holy crap Philo, do you get night blindness after turning them on and back off?

[crisis88]

Looks good!

[tcm glx]

Saaaweeeet