synergy balljoints?????? any real world feedback?

[flyinbronco]

Wes is a good guy to deal with also.

Well guys I can report that the refund is um shall we say in the mail.

My big complaint is you cannot get anyone on the phone or answer my e mails. I made three calls, waited on hold for over 20 minutes each time only to give up and leave a message that still haven't been returned. Sent three e mails that Wes finally repied to yesterday afternoon. He blamed it on the Jeepers Jamboree . I just wanted to get my darn money back. That's BS. The sad part is they still haven't changed their website that says they fit the TTB years of the Bronco but alas they only work in a straight axles. Lesson learned, this Bronco guy got no respect from Jeep guys. That is all.

[Broncodawg]

There's a thread on Pirate on the Jeep Jamboree about a wreck and fire on Cadillac Hill (exit from Rubicon out to Lake Tahoe) that closed the trail until Monday stranding a ton of rigs and people at Rubicon Springs. No dog in this hunt, just an fyi.

[78Class3]

I like polyperformance and use them when they answer their phone. I once called about a dozen times in a week looking to talk to someone about a hole flange and never got a hold of anyone. Not sure where the glitch was....

[kylesgorter]

Wes is an old friend of mine and I've known tommy for years too both great guys and they will definitely help wherever they can. Tommy is an "offroad expert" in other words a salesman/service guy where as Wes is the designated customer service guy so these things are handled by him usually. I'll talk to Wes and see what's what and maybe the word will go to the web people and change the info on the website. they sell so many parts and are expanding quickly so its been hard to keep up with demand I think and they recently split the company to manufacture their synergy line in house so I'm sure its just crazy for them still.

Maybe they will make a ttb model if there's enough demand

[flyinbronco]

Well the refund came and all is well.


I just don't get how you can run a business without answering the phones???

[philofab]

Well the refund came and all is well.


I just don't get how you can run a business without answering the phones???

They do a lot of internet and forum stuff...

That being said I have been in their shop, they do quite a bit with very little room and man power.

[kylesgorter]

They moved and expanded their new setup is pretty massive compared to before. I have no idea what's up with answering phones that's not the way you do good buisness at all.

[kylesgorter]

Spoke with some people anfd a friend of mine actually.just bought the.same balljoints for his f150 and.ifs now returning them. According to Wes and the link he sent me there is a note on the website that states the balljoints are for solid axle applications only and were specifically designed for.jk model 44s. He said there is no plans to produce ttb balljoints

[flyinbronco]

Spoke with some people anfd a friend of mine actually.just bought the.same balljoints for his f150 and.ifs now returning them. According to Wes and the link he sent me there is a note on the website that states the balljoints are for solid axle applications only and were specifically designed for.jk model 44s. He said there is no plans to produce ttb balljoints

There might be now but there wasn't when I ordered mine.



Too bad they don't make a TTB model. They looked well built. Oh well Jeep guys are funny.

[Deleted Account]

i used them. i modded the cams so i could use the cotter pins still. so far so good. the bronco is in cabo as we speak

[flyinbronco]

i used them. i modded the cams so i could use the cotter pins still. so far so good. the bronco is in cabo as we speak

I was curious how you used them Mark. The uppers were way short.

[Deleted Account]

the threads are short. but the taper is the same though. The nut goes on fine. You could use a locknut instead of the castle nut.

[kylesgorter]

Sounds like it would work to me! I def would use an all metal locking flange nut (not just the serrated) I hate nylocks.