Kel Fab Creations Bronco Build

[cs_drums]

You extend thoughs beams I sold you? haha I cant remember did i give you axles with them?

[Kel Fab Creations]

No, not yet. Hopefully in a few weeks. Gotta finish the wheels, mount glass, and get done with customer stuff first. Not enough hours in the day.

I did put the muffler on though. LOL. Sounds good.

[S.Crane]

That thing is looking good.... I'm in the valley, hope to see it on the street (and dirt) soon...Nice score at the swapmeet....

[Travisfab]

Post pics of the glass!

[Kel Fab Creations]

The glass is in the background on the pic with the two tires stacked up. Been tripping over those things too long. Kinda dreading putting the front on. Wish the inner fender wasn't one with the outer.

[Kel Fab Creations]

more parts to add to the collection. now i can start to tear it apart.


64" kit minus the rear hanger, 2 5 point harnesses, stock bucket seat sliders, and fox bumps.

[Kel Fab Creations]

Let there be light! Hopefully I'll have some output pics to show tomorrow.

[Kel Fab Creations]

Just got back from my little light test. I am very impressed with the light bar and very unimpressed with my stock headlights. LOL. The pictures don't do it justice. Looks ever better in person. I wanted to get a real feel for the bar so instead of just holding it and pointing at the dark I waited to test it till it was installed on the truck. Most of these pics are my phone sitting on top of the steering wheel to get a drivers point of view. Also keep in mind my windshield is very dirty.
Pitch dark.

Highbeams LOL

Light bar.


High beams.

Lightbar

Standing to the side.

Behind truck.

I don't have a whole lot of experience with different lights but I think this setup will do me well. Especially after I upgrade the headlights. Not sure yet if I'm gonna put lights on the bumper or not. Oh ya, this is a 40" LED light bar from prerunit on here. Thanks Javier.

[economig]

Nice pics & cool write-up for the bars.

[tcm glx]

That looks really good!! I am impressed!! Waiting for the 33" lights to show!

[Pre Run It]

Mounts for the light bar look even better in person. Cant wait to get them installed.

[Bronco_Luis]

more parts to add to the collection. now i can start to tear it apart.


64" kit minus the rear hanger, 2 5 point harnesses, stock bucket seat sliders, and fox bumps.

are you gona get rid of your rear bench seat ? if u do ill buy it off you i need one ..thanx .,.,and by the way nice wrk with the light bar man looks very sweet....

[Kel Fab Creations]

are you gona get rid of your rear bench seat ? if u do ill buy it off you i need one ..thanx .,.,and by the way nice wrk with the light bar man looks very sweet....[/quote]

I'm keep the rear bench but getting rid of the front one.

[Kel Fab Creations]

Not a huge update here but i did get one rear quarter done. My first glass install on a bronco. I'm a little less than pleased with the fit. The rear area around the taillight is all kinds of jacked up. When i paint it I'll have to do some cutting and reshaping. Overall it looks good but there is atleast a half inch gap above the light when i put it in. i tacked in a nut for the front top mount since you can't really get to the back side.

[ChaseTruck754]

Who made the glass Kelly?

[Kel Fab Creations]

Fiberwerks.

[ChaseTruck754]

There's your problem right there...

[bajascott]

i dont know why they make the wrap around the rear like that. its impossible to make it look right.
i would trim that edge off and stop the glass right before the corner.....

[Kel Fab Creations]

I like the wrap around and the tapered up rear. That's one of the reasons I bought it. The glass is pretty thin and would look nice if it was only the same shape. I understand thicknesses variances but this is a total different shape. I didn't post this to bash fiberwerks as I've never had a problem with they're ranger glass. Just wanted to post my experience. I'm sure if I went to Jason he would make it right but he is just too far from me so I'll just deal with it.

[bajascott]

i wasnt bashing, and wont compare brands. if you like it and can make it work to your specs than by all means do it,its yours. my new front clip is fiberwerx and i like it,the only fitting issues i have are my own preferance of slope to the front end, otherwise all the line are good,if i were to make fit it the way they designed it.
i like the way you did your tabs i wish the guy who installed my rear quarter did that.....