Mustang Shorties on a FSB???
-
- Posts: 2328
- Joined: Mon May 27, 2013 12:25 am
- Bronco Info: Bronco List:
- Location: Phoenix, AZ
Mustang Shorties on a FSB???
Does anyone know if a set of off the shelf 89-93 Mustang shortie headers can work? Like will they fit with a nice custom Y-pipe or just crash into the frame or cab? I’m running the urethane bushing style motor mounts btw.
If you’ve given it a go let me know!!
If you’ve given it a go let me know!!
http://www.vintageironfabworks.com
77- "Victoria"
71- "Annie" Halfcab
73- "Heloise"
96- "Cheryl"
95- Marilyn (F150)
77- "Victoria"
71- "Annie" Halfcab
73- "Heloise"
96- "Cheryl"
95- Marilyn (F150)
Re: Mustang Shorties on a FSB???
I ran a set of bbk equal length. Fox body shorties on my 96 f150 4x4 with the 302. They cleared everything fine and I just had a true didn't exhaust built to fit them. A y pipe could be made no problem
Re: Mustang Shorties on a FSB???
That's suppose to say I had a true dual exhaust built to fit them
-
- Posts: 2328
- Joined: Mon May 27, 2013 12:25 am
- Bronco Info: Bronco List:
- Location: Phoenix, AZ
Re: Mustang Shorties on a FSB???
Where are the problem areas that could be an issue potentially?
On another note- there’s a discussion here about waning use of GFB and no edit is incredibly lame!
On another note- there’s a discussion here about waning use of GFB and no edit is incredibly lame!
http://www.vintageironfabworks.com
77- "Victoria"
71- "Annie" Halfcab
73- "Heloise"
96- "Cheryl"
95- Marilyn (F150)
77- "Victoria"
71- "Annie" Halfcab
73- "Heloise"
96- "Cheryl"
95- Marilyn (F150)
- ChaseTruck754
- Spy/Ninja
- Posts: 9194
- Joined: Thu Jan 28, 2010 9:46 am
- Bronco Info: Don't have one - just old Ford trucks
- Location: Huntington Beach, CA
Re: Mustang Shorties on a FSB???
Sure the no edit can be frustrating, but step up, build your owne website & manage it & do as you wish with the edit function if you hate it so much...
Owner of only dead and forgotten projects
-
- Posts: 175
- Joined: Sun Nov 24, 2013 7:17 pm
- Bronco Info: 94 F150, 133"+8ft, 4x4, 4.9, E4OD, lots of rust
Re: Mustang Shorties on a FSB???
It's literally just a configuration option in phpBB and basically every other forum on the web has it enabled. No wonder people are sore about it.ChaseTruck754 wrote:Sure the no edit can be frustrating, but step up, build your owne website & manage it & do as you wish with the edit function if you hate it so much...
'94 F150, 4.9L, lockers at both ends
- Becks_Bronco
- Posts: 1244
- Joined: Sun Dec 20, 2009 2:12 pm
- Bronco Info: 96 Eddie Bauer, 5.8
- Location: Antioch
Re: Mustang Shorties on a FSB???
Excuse my ignorance, are the mustang shorties cheaper, more common, available used, free-re flowing etc?
Curious why one would use them over some meant for a Bronco F-Series.
Curious why one would use them over some meant for a Bronco F-Series.
-
- Posts: 2328
- Joined: Mon May 27, 2013 12:25 am
- Bronco Info: Bronco List:
- Location: Phoenix, AZ
Re: Mustang Shorties on a FSB???
Because the Bronco ones A. have the EGR bung thing on them that I don’t want, B. Are only 1 1/2” and 1 5/8” only in the Lightning version, C. They are not made but by 2 companies anymore- so little variety D. Limited on matierials made -ie none made with 304 SS.
I run a set of the Bassani units on my F150 but would like a full 304 SS option in a 1 3/4” or 1 7/8” midlength option if I went to a higher HP engine at some point. It would just be nice to start with a better off the shelf option vs a full custom setup.
I run a set of the Bassani units on my F150 but would like a full 304 SS option in a 1 3/4” or 1 7/8” midlength option if I went to a higher HP engine at some point. It would just be nice to start with a better off the shelf option vs a full custom setup.
http://www.vintageironfabworks.com
77- "Victoria"
71- "Annie" Halfcab
73- "Heloise"
96- "Cheryl"
95- Marilyn (F150)
77- "Victoria"
71- "Annie" Halfcab
73- "Heloise"
96- "Cheryl"
95- Marilyn (F150)
-
- Posts: 322
- Joined: Sun Jul 14, 2013 8:02 am
- Bronco Info: 1995 XLT Sport. 96 427w e4od obd II system........ SOLD IT
- Location: Henderson NV , Murray UT
Re: Mustang Shorties on a FSB???
This list could get very long. Cal smog laws can effect some
Would be nice to not cook starters, Must clear coil over mounting and engine cage. Not burn shifter cables. Clear frt drive shaft. Be able to change spark plugs
1.6 primary shorties will limit you at about 3500 RPM and up, And has been proven on a dyno many times Some shorties may not give any HP gains.
I had switched over to 1.6 primary Hooker Comp long tube headers on my 5.8L
Most LS motors run 1.7 primary.
I now run 1.7 primary midlength Accufab on my stroker
Would be nice to not cook starters, Must clear coil over mounting and engine cage. Not burn shifter cables. Clear frt drive shaft. Be able to change spark plugs
1.6 primary shorties will limit you at about 3500 RPM and up, And has been proven on a dyno many times Some shorties may not give any HP gains.
I had switched over to 1.6 primary Hooker Comp long tube headers on my 5.8L
Most LS motors run 1.7 primary.
I now run 1.7 primary midlength Accufab on my stroker
- Becks_Bronco
- Posts: 1244
- Joined: Sun Dec 20, 2009 2:12 pm
- Bronco Info: 96 Eddie Bauer, 5.8
- Location: Antioch
Re: Mustang Shorties on a FSB???
all legitimate reasons, appreciate it.VintageIronFab wrote:Because the Bronco ones A. have the EGR bung thing on them that I don’t want, B. Are only 1 1/2” and 1 5/8” only in the Lightning version, C. They are not made but by 2 companies anymore- so little variety D. Limited on matierials made -ie none made with 304 SS.
I run a set of the Bassani units on my F150 but would like a full 304 SS option in a 1 3/4” or 1 7/8” midlength option if I went to a higher HP engine at some point. It would just be nice to start with a better off the shelf option vs a full custom setup.
-
- Posts: 50
- Joined: Sat May 02, 2015 2:14 pm
- Bronco Info: 1993 XLT 351. Currently being built. Solo c&t beams, solo radius arms, solo shock hoops
Re: Mustang Shorties on a FSB???
i know this is an old post, but I have a set of factory shorty headers from a 86-93 mustang sitting in my garage. I will let them go for a 12 pack of beer or 2 rolls of TP