Slappy Style Go Fast with Dana 44/50 hybrid beams....

cs_drums · Post by **cs_drums** » Thu Oct 26, 2017 12:55 pm

Is a intercooler mandatory at 7psi. My blower set up is 6psi not intercooled. I’m gonna add one and bump up PSI

Sent from my iPhone using Tapatalk

powa_ranga · Post by **powa_ranga** » Thu Oct 26, 2017 7:45 pm

Intercoolers are not mandatory but they make a world of difference in multiple ways including the obvious advantage of a cooler/denser air charge, better power, and better driveability... just know that the cooler=equals better on your charge side and accept it lol...a lot of high hp drag cars will actually spray methanol as well as run on alcohol to cool the air charge, but that is a whole different world all together that I could literally spend all day talking about.

I got a lot of flack for putting my intercooler in the back on my ranger because it wasn't in direct airflow but between the increased surface area and the draft off the cab I feel I had sufficient enough heat transfer to justify having it back there....it made a noticeable temp difference that you could actually feel by touch and it also made a drastic night/day difference in power you could feel from the drivers seat.

So too sum up...yes intercooler good, heat bad.

Sent from my VS988 using Tapatalk

AussieRod · Post by **AussieRod** » Fri Oct 27, 2017 3:09 am

Actually, the correct terminology is CHARGE AIR COOLER, or AFTERCOOLER, not intercooler. Inter-coolers are mounted BEFORE or IN BETWEEN supercharger stages to cool the ingested or first stage pressurised air charge. AFTER-coolers, or charge air coolers are mounted between the supercharger outlet and the engine intake to reduce the compressed air charge temperature prior to entering the intake manifold. (Supercharger being positive displacement or turbocharger).

There is some confusion in terminology between aftercooler, intercooler, and charge-air cooler. In the past, aircraft engines would run turbochargers in stages, where the first stage compressor would feed the inlet of the second stage compressor that would further compress the air before it enters the engine. Due to the extremely high pressures that would develop, an air cooler was positioned between the first and second stage compressors. That cooler was the "Intercooler". Another cooler would be positioned after the second stage, which was the final compressor stage, and that was the "aftercooler". An aftercooler was the cooler whose outlet fed the engine.(Wikipedia).
Sorry, just my $0.02.

damon1272 · Post by **damon1272** » Fri Oct 27, 2017 5:55 am

So your saying the technical term for it is - dinglehopper. Got it.

powa_ranga · Post by **powa_ranga** » Fri Oct 27, 2017 11:48 am

More pieces to the puzzle coming together, not sure if I'll bolt these GT40's on this engine or not but its good to have them...finally home for 3 days after 3 weeks away so hopefully I can get something done in this pile, shipping off to Texas for work on Monday lol.

Sent from my VS988 using Tapatalk

powa_ranga · Post by **powa_ranga** » Sat Oct 28, 2017 3:10 pm

Not sure if this is considered progress or not

Sent from my VS988 using Tapatalk

funinthesun95 · Post by **funinthesun95** » Mon Oct 30, 2017 10:17 am

oh boy....

powa_ranga · Post by **powa_ranga** » Thu Nov 02, 2017 6:25 pm

funinthesun95 wrote:oh boy....

Let me know when you wanna buy it back lol

Sent from my VS988 using Tapatalk

Wrightracing.net · Post by **Wrightracing.net** » Fri Nov 03, 2017 3:27 am

powa_ranga wrote:Not sure if this is considered progress or not

Sent from my VS988 using Tapatalk

Is that a Turbo going in there?

Sent from my SM-T900 using Tapatalk

powa_ranga · Post by **powa_ranga** » Fri Nov 03, 2017 9:05 am

Wrightracing.net wrote:
powa_ranga wrote:Not sure if this is considered progress or not

Sent from my VS988 using Tapatalk
Is that a Turbo going in there?

Sent from my SM-T900 using Tapatalk

Yep

Sent from my VS988 using Tapatalk

funinthesun95 · Post by **funinthesun95** » Fri Nov 03, 2017 1:38 pm

powa_ranga wrote:
funinthesun95 wrote:oh boy....
Let me know when you wanna buy it back lol

Sent from my VS988 using Tapatalk

nice

powa_ranga · Post by **powa_ranga** » Sun Nov 26, 2017 4:05 pm

Checking clearances for the turbo piping and building the hotside...39's take up a lot of real estate

Sent from my VS988 using Tapatalk

Needles929 · Post by **Needles929** » Wed Nov 29, 2017 2:54 pm

Woooow!

powa_ranga · Post by **powa_ranga** » Sat Dec 02, 2017 5:24 pm

Hotside completely tacked up and ready to weld, need to rig up some sort of mount solution to take the weight of the turbo off the pipes but it's in its home, I can still swing it 3-4 inches either way if I need to since it has v band clamps...starting on intercooler and piping next.

Sent from my VS988 using Tapatalk

funinthesun95 · Post by **funinthesun95** » Mon Dec 04, 2017 10:42 am

will the mount come off the Cross bar to support turbo?

cs_drums · Post by **cs_drums** » Mon Dec 04, 2017 4:05 pm

If you mount to cage I’d think you need to do rubber bushing, right? Cause even with poly mounts the motor will probably move some in relation to frame/cage

Sent from my iPhone using Tapatalk

powa_ranga · Post by **powa_ranga** » Mon Dec 04, 2017 8:13 pm

Not sure how I am going to mount it, was thinking of building simple brackets off the header bolts or intake manifold bolts, that way everything stays engine mounted and moves together...I'll have to look at it closer when I get time, if I mount it off the cage then yes, it will have to rubber mounted..the merge collector and up pipes will be rubber mounted to the frame.

Sent from my VS988 using Tapatalk

VintageIronFab · Post by **VintageIronFab** » Mon Dec 04, 2017 9:12 pm

What about some thick aluminum that uses the 4 carb bolts- obviously with a hole in the middle - carb spacer / turbo mount??

powa_ranga · Post by **powa_ranga** » Mon Dec 04, 2017 9:33 pm

Interesting idea but I would be concerned with it having too much leverage hanging off the side and either warping the carb flange or creating a vacuum leak.

Sent from my VS988 using Tapatalk

funinthesun95 · Post by **funinthesun95** » Wed Dec 06, 2017 4:54 pm

cs_drums wrote:If you mount to cage I’d think you need to do rubber bushing, right? Cause even with poly mounts the motor will probably move some in relation to frame/cage

Sent from my iPhone using Tapatalk

cross tube bushing same as motor

but, yes no matter how much you tie things in you will have some movement or vibration.....always ( like you are saying Brian)