mild 351w roller motor, harness

Garlic Bronco · Post by **Garlic Bronco** » Fri Jan 22, 2016 12:30 pm

hey man not trying to ruffle and feathers. good luck with selling it and getting something in that sweet ride.

Car54 · Post by **Car54** » Sun Jan 24, 2016 8:58 pm

Read all posts never said how much horsepower to the wheels with all that dyno time

cs_drums · Post by **cs_drums** » Mon Jan 25, 2016 8:38 am

It was in his build thread. 200hp to the rear wheels.

hollandermotorsports · Tue Jan 26, 2016 10:29 pm

Yes it was 215hp to the rear wheels I don't recall the tq but I believe it was 230ish I'll check the sheet next time I think of it. That data was with 3rd gear pulls 4.88 gears and 37" tires and a c6.

cudakid · Post by **cudakid** » Tue Mar 08, 2016 2:46 am

damn I wish I would have I saw this post while it was still available! Would have snatched it up....

hollandermotorsports · Tue Mar 08, 2016 10:40 am

Motor is still available but not till after Norra with about 1500-2000 miles on it. Deal fell apart due to financial reasons so deposit was refunded.

hollandermotorsports · Wed Jul 27, 2016 1:46 pm

The motor is back up for sale. It runs great I just want more power and the time has come to get it done. The motor has about 4,000-5,000 miles on it with no issues. I have decided Carb is probably my best bet so it will be sold complete with all efi stuff including computer, standalone engine management harness, all the edelbrock intake, bbk throttle body and that kind of stuff. I want $5500 or really close to it for this stuff I have a lot in all of this package. It will be available after Temecula Off-road nights. Dyno sheets will be provided to any potential buyers and you are welcome to come by and go for a ride and hear it run. Trust me this is a great motor and set up. Will consider separating the package up but I will not disassemble motor at all.

hollandermotorsports · Wed Jul 27, 2016 3:49 pm

Harness and computer are spoken for motor is 3500 cash

cs_drums · Post by **cs_drums** » Fri Sep 30, 2016 8:44 am

This motor still available? Is the bottom end rebuild or did you just add the top end components to the low mile motor.

Sent from my iPhone using Tapatalk

hollandermotorsports · Fri Sep 30, 2016 11:12 am

Ya few people have said they want or need it but nothing so it is still in the bronco and no sense in pulling it until there is a deposit. It runs good so not in a hurry. I have my new 408w that is ready to go in aside from some intake parts.

Bottom end was gone through new bearings and rings oil pump, seals ect. and a hone job nothing to radical.

I will be driving it to Big Bear next weekend so it will get another 300-400 miles.

cs_drums · Post by **cs_drums** » Fri Sep 30, 2016 1:21 pm

What size injectors?

Sent from my iPhone using Tapatalk

cs_drums · Post by **cs_drums** » Fri Sep 30, 2016 1:29 pm

Also could the data from your tune be burned to a chip for OBD1 speed density?

Sent from my iPhone using Tapatalk

hollandermotorsports · Fri Sep 30, 2016 1:40 pm

I believe either 27lb or 24lb whatever was suggested with some margin by JBA for the mods. We can extract data to load on a chip. It would have to be done by the tuner. I do not have the tools to do that.

hollandermotorsports · Fri Sep 30, 2016 2:04 pm

cs_drums wrote:Also could the data from your tune be burned to a chip for OBD1 speed density?

Sent from my iPhone using Tapatalk

Feel free to give me a call.

hollandermotorsports · Mon Oct 24, 2016 11:03 am

Ok last bump new motor will be here this week. Honestly this motor in it runs so good im probably just going to run it till it needs to be replaced or until this one sells. Im dropping the price to $2800 thats my bottom dollar. And if you want the tune the cost to transfer is on buyer.

S00TLYFE · Post by **S00TLYFE** » Tue Oct 25, 2016 9:01 am

good price Brandon, GLWS

hollandermotorsports · Thu Oct 27, 2016 2:28 pm

Pending sale.

hollandermotorsports · Sat Oct 29, 2016 1:14 pm

Sold.