snowman429's 93 Bronco v2.0
-
- Posts: 1677
- Joined: Mon Mar 03, 2014 8:45 am
- Bronco Info: 1996 EB 351W!! First Bronco!! Plan: Prerunner/ Trail Rig/ SHTF All around Rig
Re: snowman429's 93 Bronco v2.0
Glad to hear you didn't suffer any vision damage .
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
Back from the dead. After getting screwed over from someone I thought was a friend and my dad moving in fit the summer, I didn't get anything done on the bronco. His stuff was more important. Now that he's gone the bronco is getting some much deserved attention. Work has been extremely slow cause I only have use of my right hand. ( had surgery on my left wrist) But I did manage to get my headers installed with one hand, took two days but they are installed.
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
-
- Posts: 1677
- Joined: Mon Mar 03, 2014 8:45 am
- Bronco Info: 1996 EB 351W!! First Bronco!! Plan: Prerunner/ Trail Rig/ SHTF All around Rig
Re:
snowman429 wrote:Thanks to my awesome wife buying me all my steel braided lines and fittings for my brakes, my bronco is one step closer to being on the road. All the brake plumbing is done new pads and calipers, wheel bearings installed. Only thing left us to bleed the system.
That's a keeper right there!!
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
snowman429's 93 Bronco v2.0
Getting some little stuff finished up. Two of the three seats mounted are mounted. I still have some welding to finish up on engine cage. The next big project will be the fiberglass dash.
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
snowman429's 93 Bronco v2.0
Little update, dash is in, ZF is out. Since I decided to go back to the e4od I had to remove the MAF conversion kit I had on it. Luckily for me the truck I got the trans out of was a MAF truck so I pulled the intake hoses, sensor and computer. Then the fun part of re-pinning the 60 pin connector, running new injector and MAF wires. Took a few hours but wasn't as bad as I thought. Today I ordered my punisher VB and winters shifter.
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
snowman429's 93 Bronco v2.0
Well after about 3.5 years, a lot of money, a very understanding wife, and three wrist surgeries that have rendered my left hand pretty much useless she's back on the road. Still have some sms stuff to finish up but she's drivable.
Sent from my SM-G930V using Tapatalk
Sent from my SM-G930V using Tapatalk
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
snowman429's 93 Bronco v2.0
Well little update, Betty has a new heart. 408w, edelbrock heads, comp roller cam, edelbrock rpm air gap intake. Going to be running a Holley sniper efi and a (Thanks to Matt) US shifts quick 4 trans controller.
Sent from my SM-G960U using Tapatalk
Sent from my SM-G960U using Tapatalk
snowman429's 93 Bronco v2.0
Nice upgrades, what trans ? you should keep that two-tone paint.
Sent from my iPhone using Tapatalk Pro
Sent from my iPhone using Tapatalk Pro
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
snowman429's 93 Bronco v2.0
Currently a stock e4od with a punisher valve body. Im still debating on paint. I'm just not sure about the two tone with the flare on the front fenders.
Sent from my SM-G960U using Tapatalk
Sent from my SM-G960U using Tapatalk
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
snowman429's 93 Bronco v2.0
Well she's up and running now. Sounds good can't wait to get some tuning done.
Sent from my SM-G960U using Tapatalk
Sent from my SM-G960U using Tapatalk
-
- Posts: 55
- Joined: Wed May 30, 2012 2:08 pm
- Bronco Info: 79 Bronco, 545ci stroker, TTB conversion, 4.5” fabricated beams/3.5” bypasses etc, AutoFab Glass
- Location: Boise idaho
Re: snowman429's 93 Bronco v2.0
Cool to see another GFB guy in Idaho! I’ve been stationed out near Boise for the last few years. bronco’s new heart is looking good!
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
Re: snowman429's 93 Bronco v2.0
Yeah, not many of us in this area. She's a runner now, can't wait to hit St. Anthony next spring.
Authorized AMSOIL Synthetic oils dealer
For more information or to purchase Amsoil products visit idahosyntheticoils.myamsoil.com
For more information or to purchase Amsoil products visit idahosyntheticoils.myamsoil.com
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
snowman429's 93 Bronco v2.0
Well just picked up a 95 Bronco for my son. Wasn't really looking but couldn't pass the deal. It's got a 4" lift, solid axle swap, 9" lockers front and rear 35's. Just turned 122000. It needs some work, mostly interior but is drivable. Best of all, got it for $1200
Sent from my SM-G960U using Tapatalk
Sent from my SM-G960U using Tapatalk
-
- Posts: 2912
- Joined: Wed Dec 22, 2010 10:39 am
- Bronco Info: 94 5.8 Bronco w/dreams of being finished
snowman429's 93 Bronco v2.0
Wow that sounds like a smokin deal!
Sent from my moto x4 using Tapatalk
Sent from my moto x4 using Tapatalk
- snowman429
- Posts: 201
- Joined: Sun Jun 10, 2012 2:07 pm
- Bronco Info: 93 Bronco alot of work
- Location: Rigby, Idaho
snowman429's 93 Bronco v2.0
It runs and rides pretty good. Steering is a little loose, but that easily fixed. He's super excited. I had to snap this picture today.
Sent from my SM-G960U using Tapatalk
Sent from my SM-G960U using Tapatalk