Page 1 of 1
Looking for a NorCal/Reno fabricator
Posted: Fri Aug 26, 2022 11:40 am
by KrondoUSA
Hello, I’m looking for a reputable shop in the NorCal/Reno area to build me a swing steering setup and front bumper for my 96. I’m located in Susanville. Any input helps! Thanks!
Re: Looking for a NorCal/Reno fabricator
Posted: Mon Aug 29, 2022 3:02 pm
by PotBellyWill
Would love to know the same. I am in Reno and haven't found anyone yet. I did have Folbeck do a driveshaft for me and they did good work with that, but I would love a Ford/TTB specialist.
Re: Looking for a NorCal/Reno fabricator
Posted: Mon Aug 29, 2022 4:56 pm
by Nick
Any of the major socal shops will ship.
Re: Looking for a NorCal/Reno fabricator
Posted: Mon Aug 29, 2022 5:26 pm
by PotBellyWill
No doubt. I am from So Cal so I'm a big fan of Solo and Desolate. Had some things shipped up by Desolate just recently.
Re: Looking for a NorCal/Reno fabricator
Posted: Thu Sep 01, 2022 9:51 pm
by KrondoUSA
Between a newborn, house remodel and work I don’t have the time to take on the project anymore and I’d like to get it completely done. I have the parts for the steering, can even supply the material for the bumper if needed.
Re: Looking for a NorCal/Reno fabricator
Posted: Mon Sep 05, 2022 7:10 pm
by 24hours
You have a few options. First would be Samco Fabrication. Sam got his start with Rod Hall. He races and so do his employees. His last fab guy went onto Menzies as fab/ co driver. Sam, Alex and co are great guys. I have gone to multiple races with these guys as support in NV as well as Baja.
Another shop that is building a nice reputation is Silver State off-road. I personally don’t know them but a few trusted friends in the industry speak well of them.
Finally in NV you have Randy Slawson of Bomber Fab. Randy has multiple King of the Hammer wins.
Nate of Nate’s 4X has built numerous high dollar builds, not a go fast guy though.
Nothing wrong with Jim Foley of Folbeck, but he’s just a bolt on guy. His manager, Donny used to own a shop in town too. Bolt on shelf stuff and general maintenance.
If you don’t want to support a NV business I’d look at Rockhound in Auburn.
Re: Looking for a NorCal/Reno fabricator
Posted: Tue Sep 06, 2022 8:57 pm
by Nick
KrondoUSA wrote: ↑Thu Sep 01, 2022 9:51 pm
Between a newborn, house remodel and work I don’t have the time to take on the project anymore and I’d like to get it completely done. I have the parts for the steering, can even supply the material for the bumper if needed.
Most bumpers are bolt on, no fab work need.
Re: Looking for a NorCal/Reno fabricator
Posted: Tue Sep 06, 2022 9:00 pm
by Nick
Maybe minimal at the frame horns. But any shop can do that for you. I guess what i'm saying, buy the parts that you want, that you know work, and any decent shop can install it. The hard part is done.
Re: Looking for a NorCal/Reno fabricator
Posted: Wed Sep 07, 2022 6:22 am
by hobbyturnedobsession
Nick wrote: ↑Tue Sep 06, 2022 9:00 pm
Maybe minimal at the frame horns. But any shop can do that for you. I guess what i'm saying, buy the parts that you want, that you know work, and any decent shop can install it. The hard part is done.
This could help you out quite a bit. Buy a complete kit that someone can bolt on for you. That way, all the parts go together and you can have a bolt on shop do the install. Your hourly rate should be less, and it would save considerable time because building custom means a ton of cycling. I would hedge a bet that it would cost you 3-5 times as much to have a shop build it than it would to buy the kit and have someone bolt it up.
Re: Looking for a NorCal/Reno fabricator
Posted: Wed Sep 07, 2022 9:47 am
by PotBellyWill
24hours wrote: ↑Mon Sep 05, 2022 7:10 pm
You have a few options. First would be Samco Fabrication. Sam got his start with Rod Hall. He races and so do his employees. His last fab guy went onto Menzies as fab/ co driver. Sam, Alex and co are great guys. I have gone to multiple races with these guys as support in NV as well as Baja.
Another shop that is building a nice reputation is Silver State off-road. I personally don’t know them but a few trusted friends in the industry speak well of them.
Finally in NV you have Randy Slawson of Bomber Fab. Randy has multiple King of the Hammer wins.
Nate of Nate’s 4X has built numerous high dollar builds, not a go fast guy though.
Nothing wrong with Jim Foley of Folbeck, but he’s just a bolt on guy. His manager, Donny used to own a shop in town too. Bolt on shelf stuff and general maintenance.
If you don’t want to support a NV business I’d look at Rockhound in Auburn.
This is a great list! I have also heard good things about Silver State.
Re: Looking for a NorCal/Reno fabricator
Posted: Wed Sep 07, 2022 9:55 am
by 24hours
Re: Looking for a NorCal/Reno fabricator
Posted: Wed Sep 07, 2022 6:51 pm
by KrondoUSA
Thank you for the great list Nick! I’ll make some calls! The steering seems like a fairly straight forward install, but I cut the old tube bumper and frame horns off after an accident so the bolt on bumpers are out of the question for me now. Would’ve loved to get desolates new bolt on.
Re: Looking for a NorCal/Reno fabricator
Posted: Thu Sep 08, 2022 12:07 pm
by PotBellyWill
KrondoUSA wrote: ↑Wed Sep 07, 2022 6:51 pm
Thank you for the great list Nick! I’ll make some calls! The steering seems like a fairly straight forward install, but I cut the old tube bumper and frame horns off after an accident so the bolt on bumpers are out of the question for me now. Would’ve loved to get desolates new bolt on.
Let me know if you ever want to meet up and talk Broncos. I was actually born in Portola and wanted to get back up into the area so we just moved to Reno last year.
