Jim & Paige's Bronco

Rmc · Post by **Rmc** » Wed Dec 09, 2015 1:20 am

What kind of headers?

1Hondalover · Post by **1Hondalover** » Wed Dec 09, 2015 7:09 am

Bassani raw steel for my coating TBD. We have their y-pipe as well, and I think we're going to have RPM in Oceanside put it all together with new muffler out the back. I like the side exit many of the Broncos use, but the links are a bit of a problem with inboard exhaust. I think Richard is pretty crafty so we'll see what kinds of ideas he has.

dtbback · Post by **dtbback** » Wed Dec 09, 2015 7:13 am

You can cut the sheet metal where everyone has there under the bed shock tower to route the pipe over the frame and side exit. Should be plenty of space there for a 3, heck even a 4 inch pipe. Should be well above the links.

tcm glx · Post by **tcm glx** » Wed Dec 09, 2015 9:05 am

1Hondalover wrote:Bassani raw steel for my coating TBD. We have their y-pipe as well, and I think we're going to have RPM in Oceanside put it all together with new muffler out the back. I like the side exit many of the Broncos use, but the links are a bit of a problem with inboard exhaust. I think Richard is pretty crafty so we'll see what kinds of ideas he has.

I think you are going to be very happy with the Bassani setup, especially with the Y Pipe... Cant wait to see/hear it! KOH is less than two months away!

hollandermotorsports · Thu Dec 10, 2015 9:05 am

dtbback wrote:You can cut the sheet metal where everyone has there under the bed shock tower to route the pipe over the frame and side exit. Should be plenty of space there for a 3, heck even a 4 inch pipe. Should be well above the links.

That interferes with upper links on most linked broncos. We actually had to notch that for my upper links to clear at full bump in the rear. Richard (RPM) is a good choice he built fender well header and side exit exhaust for mine and could not be happier with his quality. He has done a few vehicles for me this year with complete custom headers and exhaust complete stainless units and he has been on time and in most cases under budget from the original quote.

cs_drums · Post by **cs_drums** » Thu Dec 10, 2015 10:35 am

Richard is the man. Not to cool for the low budget guys like me but is the best in business for high end as well.

1Hondalover · Post by **1Hondalover** » Fri Dec 11, 2015 7:53 am

If Richard's work is as good as his communication I have no doubt about RPM's success. They actually answer the phone and email and everything.....just like a real business. I'm looking forward to doing business with them.

tcm glx · Post by **tcm glx** » Fri Dec 11, 2015 10:38 am

1Hondalover wrote:If Richard's work is as good as his communication I have no doubt about RPM's success. They actually answer the phone and email and everything.....just like a real business. I'm looking forward to doing business with them.

HAHAHA, you'd think that was business 101!! Blows my mind how some people do business nowadays.

1Hondalover · Post by **1Hondalover** » Wed Dec 16, 2015 6:30 pm

Shipping before the end of the year they tell me.....

: J Coffey 5-Row CM (3) (Large).JPG (459.32 KiB) Viewed 1037 times

Post by **SteveG** » Wed Dec 16, 2015 8:01 pm

Fancy!

dtbback · Post by **dtbback** » Wed Dec 16, 2015 8:08 pm

Is that a radiator?

1Hondalover · Post by **1Hondalover** » Thu Dec 17, 2015 6:04 pm

The start of one yes.

1Hondalover · Post by **1Hondalover** » Mon Dec 21, 2015 2:00 pm

http://www.gofastbroncos.com/forum/view ... =15&t=7702

On their way to Swain.....

: IMG_9653 (Large).JPG (433.81 KiB) Viewed 854 times

: IMG_9657 (Large).JPG (257.22 KiB) Viewed 854 times

ChaseTruck754 · Post by **ChaseTruck754** » Mon Dec 21, 2015 3:13 pm

Cool. Are they trying to coat both inside & out, or just the outside? Did they give you a quote on price for the coating yet? If so, do you mind sharing?

1Hondalover · Post by **1Hondalover** » Tue Dec 22, 2015 4:37 pm

They only coat the outside for $350. I think the shipping both ways is going to net me right about $500 all in.

ChaseTruck754 · Post by **ChaseTruck754** » Tue Dec 22, 2015 4:44 pm

Wow. Hopefully that stuff works as well as the road race guys say!

1Hondalover · Post by **1Hondalover** » Tue Dec 22, 2015 5:11 pm

Last night I was eating a few cookies but didn't finish them. This morning they were gone and I found this in their place.

: IMG_9682 (Large).JPG (279.96 KiB) Viewed 763 times

: IMG_9685 (Large).JPG (307.58 KiB) Viewed 763 times

: IMG_9700 (Large).JPG (292.93 KiB) Viewed 763 times

: IMG_9699 (Large).JPG (296.95 KiB) Viewed 763 times

: IMG_9703 (Large).JPG (338.06 KiB) Viewed 763 times

Wrightracing.net · Post by **Wrightracing.net** » Tue Dec 22, 2015 6:12 pm

Paige/Santa's helper is the best!!!!

ChaseTruck754 · Post by **ChaseTruck754** » Tue Dec 22, 2015 6:24 pm

I WISH I could trade cookies for parts of that level - rad!

1Hondalover · Post by **1Hondalover** » Wed Dec 23, 2015 7:16 am

Wrightracing.net wrote:Paige/Santa's helper is the best!!!!

Of course I'm biased David.....in my book Paige is the best. Thanking the Man above as well as my lucky stars most every day for her, and never lose sight of how fortunate I am to have a wife that wants to GF in the B as much as I do.

Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: Jim & Paige's Bronco

Re: