snowman429's 93 Bronco v2.0

dtbback · Post by **dtbback** » Fri Apr 17, 2015 6:58 am

Glad to hear you didn't suffer any vision damage .

snowman429 · Post by **snowman429** » Fri Dec 18, 2015 4:06 pm

Back from the dead. After getting screwed over from someone I thought was a friend and my dad moving in fit the summer, I didn't get anything done on the bronco. His stuff was more important. Now that he's gone the bronco is getting some much deserved attention. Work has been extremely slow cause I only have use of my right hand. ( had surgery on my left wrist) But I did manage to get my headers installed with one hand, took two days but they are installed.

snowman429 · Post by **snowman429** » Fri Jan 15, 2016 2:59 pm

Thanks to my awesome wife buying me all my steel braided lines and fittings for my brakes, my bronco is one step closer to being on the road. All the brake plumbing is done new pads and calipers, wheel bearings installed. Only thing left us to bleed the system.

dtbback · Post by **dtbback** » Fri Jan 15, 2016 3:50 pm

snowman429 wrote:Thanks to my awesome wife buying me all my steel braided lines and fittings for my brakes, my bronco is one step closer to being on the road. All the brake plumbing is done new pads and calipers, wheel bearings installed. Only thing left us to bleed the system.

That's a keeper right there!!

snowman429 · Post by **snowman429** » Sat Jan 16, 2016 8:23 pm

She is defiantly a keeper. She also got me my mastercraft seats and 5 point harness for Xmas.

snowman429 · Post by **snowman429** » Fri Jan 22, 2016 3:44 pm

Getting closer, brakes system bled.

snowman429 · Post by **snowman429** » Mon Feb 01, 2016 7:07 pm

Getting some little stuff finished up. Two of the three seats mounted are mounted. I still have some welding to finish up on engine cage. The next big project will be the fiberglass dash.

snowman429 · Post by **snowman429** » Tue Feb 02, 2016 4:35 pm

So after staring at the factory dash and fiberglass dash for a while today, I think I'm going to stick with the factory one.

snowman429 · Post by **snowman429** » Fri Feb 26, 2016 3:10 pm

Little update, dash is in, ZF is out. Since I decided to go back to the e4od I had to remove the MAF conversion kit I had on it. Luckily for me the truck I got the trans out of was a MAF truck so I pulled the intake hoses, sensor and computer. Then the fun part of re-pinning the 60 pin connector, running new injector and MAF wires. Took a few hours but wasn't as bad as I thought. Today I ordered my punisher VB and winters shifter.

snowman429 · Post by **snowman429** » Sun Mar 27, 2016 9:17 am

E4OD is in, and she runs. Been over two years since I last started it, hit the key and she came to life. Next on the list is the installation of the punisher and the winters shifter.

snowman429 · Post by **snowman429** » Sun Apr 30, 2017 2:58 pm

Well after about 3.5 years, a lot of money, a very understanding wife, and three wrist surgeries that have rendered my left hand pretty much useless she's back on the road. Still have some sms stuff to finish up but she's drivable.

Sent from my SM-G930V using Tapatalk

snowman429 · Post by **snowman429** » Sun Oct 28, 2018 7:32 pm

Well little update, Betty has a new heart. 408w, edelbrock heads, comp roller cam, edelbrock rpm air gap intake. Going to be running a Holley sniper efi and a (Thanks to Matt) US shifts quick 4 trans controller.

Sent from my SM-G960U using Tapatalk

Bajaluv · Post by **Bajaluv** » Mon Oct 29, 2018 5:57 pm

Nice upgrades, what trans ? you should keep that two-tone paint.

Sent from my iPhone using Tapatalk Pro

snowman429 · Post by **snowman429** » Tue Oct 30, 2018 1:48 pm

Currently a stock e4od with a punisher valve body. Im still debating on paint. I'm just not sure about the two tone with the flare on the front fenders.

Sent from my SM-G960U using Tapatalk

snowman429 · Post by **snowman429** » Sat Nov 10, 2018 9:57 pm

Well she's up and running now. Sounds good can't wait to get some tuning done.

Sent from my SM-G960U using Tapatalk

t.r.c · Post by **t.r.c** » Tue Dec 11, 2018 7:57 pm

Cool to see another GFB guy in Idaho! I’ve been stationed out near Boise for the last few years. bronco’s new heart is looking good!

snowman429 · Post by **snowman429** » Wed Dec 12, 2018 9:01 am

Yeah, not many of us in this area. She's a runner now, can't wait to hit St. Anthony next spring.

snowman429 · Post by **snowman429** » Thu Apr 04, 2019 4:35 pm

Well just picked up a 95 Bronco for my son. Wasn't really looking but couldn't pass the deal. It's got a 4" lift, solid axle swap, 9" lockers front and rear 35's. Just turned 122000. It needs some work, mostly interior but is drivable. Best of all, got it for $1200

Sent from my SM-G960U using Tapatalk

cs_drums · Post by **cs_drums** » Sat Apr 06, 2019 9:00 am

Wow that sounds like a smokin deal!

Sent from my moto x4 using Tapatalk

snowman429 · Post by **snowman429** » Sat Apr 06, 2019 8:14 pm

It runs and rides pretty good. Steering is a little loose, but that easily fixed. He's super excited. I had to snap this picture today.

Sent from my SM-G960U using Tapatalk