95 Black Bronco

Rmc · Post by **Rmc** » Wed Nov 18, 2015 12:40 am

Might want to look at power steering solutions and Psc. Psc has a full kit for much less than Howe. Not real sure how high the quality is though but it's a big seller with the jeep crowd. Might be worth looking into.

motoxscott · Post by **motoxscott** » Wed Nov 18, 2015 5:46 pm

Charlie @ PSS is good .... stay away from PSC. Had some friends get their stuff and wasn't happy with the quality compared to Lee, Howe, PSS.

- Scott

C H O · Post by **C H O** » Wed Nov 18, 2015 9:27 pm

Talked to Bobby at solo the other day, he was super helpful. Think im going to run their setup using a rebuilt ported box, Howe t/c pump, resevoir with filter, pulley and cooler.

Rmc · Post by **Rmc** » Thu Nov 19, 2015 12:22 am

Can't go wrong with Howe.

hollandermotorsports · Thu Nov 19, 2015 7:00 am

C H O wrote:Talked to Bobby at solo the other day, he was super helpful. Think im going to run their setup using a rebuilt ported box, Howe t/c pump, resevoir with filter, pulley and cooler.

Good choice buddy.

zachwabbit · Post by **zachwabbit** » Thu Nov 19, 2015 10:10 am

Dang dude that rear bumper is clean!! Hoping to have something similar made for mine soon

C H O · Post by **C H O** » Thu Dec 03, 2015 9:15 pm

Some goodies!

Post by **SteveG** » Thu Dec 03, 2015 9:31 pm

Bad. Ass. Looking damn good!

dtbback · Post by **dtbback** » Thu Dec 03, 2015 9:58 pm

That center console is beautiful!!! How did you make it?

C H O · Post by **C H O** » Thu Dec 03, 2015 10:41 pm

Curt at crb built it, it is blended aluminum, same one that was in Gary's red bronco

cs_drums · Post by **cs_drums** » Fri Dec 04, 2015 7:43 am

So tight!!!

cbw · Post by **cbw** » Sat Dec 05, 2015 6:56 am

always impressed with your work cho.

C H O · Post by **C H O** » Sat Mar 19, 2016 8:38 pm

Put in some hours this weekend to install the new steering setup, also double sheered a pair of spindles, welded a backing plate, and put fresh ball joints in. Just need to bleed breaks and the steering

keenanduran1 · Post by **keenanduran1** » Sun Mar 20, 2016 10:58 pm

sexxx

Seabass · Post by **Seabass** » Tue Mar 22, 2016 12:01 pm

Did you have the stops added in the box?

dtbback · Post by **dtbback** » Wed Jun 15, 2016 1:41 pm

C H O wrote:Got a bunch to tubes done today, got the cage all tacked up and slid it out the back to weld an paint. Still have to to do corner gussets and window v tubes. The cage is 2" and 1.75" fully tig welded, goes through the firewall in 4 spots, fully sealed, stock dash and stock headliner. My seats should be done in a week stoked to see it taking shape!
ImageUploadedByTapatalk1394926443.737621.jpg

Hey Cho,

What diameter is the A-pillar cross tube?

carlover · Post by **carlover** » Wed Oct 05, 2016 9:20 am

What rear spring rate did you end up with? I'm looking into building a similar setup and need a good starting point for springs.

De$ertBronco · Post by **De$ertBronco** » Wed Oct 05, 2016 10:11 am

Bronco is for sale, someone buy this black beauty! http://www.race-dezert.com/classifieds/ ... &id=115400

95 Black Bronco

Re: 95 Black Bronco

Re: 95 Black Bronco

95 Black Bronco

Re: 95 Black Bronco

Re: 95 Black Bronco

Re: 95 Black Bronco

95 Black Bronco

Re: 95 Black Bronco

Re: 95 Black Bronco

95 Black Bronco

95 Black Bronco

Re: 95 Black Bronco

95 Black Bronco

Re: 95 Black Bronco

Re: 95 Black Bronco

Re: 95 Black Bronco

Re: 95 Black Bronco

Re: 95 Black Bronco