95 Black Bronco
-
- Posts: 2912
- Joined: Wed Dec 22, 2010 10:39 am
- Bronco Info: 94 5.8 Bronco w/dreams of being finished
Re: 95 Black Bronco
Simple when it needs an engine, cut the cross tube and reinstall with tube clamps. No need to spend the time and money to install tube clamps until removal is needed.
Re: 95 Black Bronco
Bingo, thanks Brian.
-
- Posts: 2912
- Joined: Wed Dec 22, 2010 10:39 am
- Bronco Info: 94 5.8 Bronco w/dreams of being finished
Re: 95 Black Bronco
NO prob Cho, my bronco suffers from the same non-removable engine right now too
-
- Posts: 2328
- Joined: Mon May 27, 2013 12:25 am
- Bronco Info: Bronco List:
- Location: Phoenix, AZ
Re: 95 Black Bronco
That makes sense really. You gonna use the interlocking clamps or the ones that just lay together and bolt together with 2 bolts?
Re: 95 Black Bronco
Billet interlocking
-
- Posts: 110
- Joined: Sun Sep 09, 2012 3:26 pm
- Bronco Info: 1992 EB, current build, 44/50 beams, 10.5 axle, 6BT swap, gofast
- Location: Jamul, CA
Re: 95 Black Bronco
Bronco looks amazing CHO. I had a question, what size UMP is that and how much HP is it good for? I just bought the 3" outlet 4" inlet one and I'm wondering it it's gonna be enough.
- Andy Jones
- Posts: 2205
- Joined: Tue Dec 08, 2009 2:47 pm
- Bronco Info: In the Works!
- Location: Canyon Lake,ca
- Contact:
Re: 95 Black Bronco
Bronco is coming along great ! Can't wait to make mine a roller, so I can give you call too finish it !
-
- Posts: 292
- Joined: Wed Aug 11, 2010 7:25 pm
- Bronco Info: 1991 351. lightweight special
Re: 95 Black Bronco
Some links on the horizon? Lolol
-
- El Jefe
- Posts: 6026
- Joined: Tue Oct 09, 2012 10:22 pm
- Bronco Info: 94 bronco xlt prerunner
- Location: IE SoCal
- Contact:
Re: 95 Black Bronco
What?
Have you seen it recently or something mike?
Have you seen it recently or something mike?
-
- Posts: 2912
- Joined: Wed Dec 22, 2010 10:39 am
- Bronco Info: 94 5.8 Bronco w/dreams of being finished
Re: 95 Black Bronco
Did anyone really think Cho was not gonna link it?! Haha
He is gonna do it just to make me jealous haha
He is gonna do it just to make me jealous haha
-
- El Jefe
- Posts: 6026
- Joined: Tue Oct 09, 2012 10:22 pm
- Bronco Info: 94 bronco xlt prerunner
- Location: IE SoCal
- Contact:
Re: 95 Black Bronco
You guys act like I should have known.
- tcm glx
- Peanut Butter
- Posts: 7303
- Joined: Tue Dec 08, 2009 11:19 am
- Bronco Info: 93 Ford Bronco 5.8
- Location: Riverside Ca
- Contact:
Re: 95 Black Bronco
Rmc wrote:You guys act like I should have known.
You asked him on the previous page of links were on the horizon and he said yes.... So yes you should have! Hahaha
-
- El Jefe
- Posts: 6026
- Joined: Tue Oct 09, 2012 10:22 pm
- Bronco Info: 94 bronco xlt prerunner
- Location: IE SoCal
- Contact:
Re: 95 Black Bronco
Tony stop jumping on the band wagon. I asked he said yessir and I moved on. Mr cox chuckled about me even asking and Brian acted as though I should expect nothing less. First off I've never met the guy, second why is that you guys think I should have guessed that he would put a new dress on the pig as well as lipstick. I don't know cho his reputation or his history. So remind me agian why I would have known. It's not a stupid question, Stop acting as though it is.
-
- Posts: 2912
- Joined: Wed Dec 22, 2010 10:39 am
- Bronco Info: 94 5.8 Bronco w/dreams of being finished
Re: 95 Black Bronco
I was taking a jab at Cho because he was saying he was gonna keep it simple. His other work shown on this sight, Black Lightening & 6 seat super suburban, would lead everyone to believe he is far from a simple builder and will likely go more than simple.C H O wrote:cs_drums wrote:C H O wrote:Time to start focusing on the front, started a pair of radius arm mounts tonight, and am picking up a pair of stock beams from a member on here this weekend to truss and extend. Still need to finish the rear overlay and weld washers, the two vertical tabs are for a crossbar/transfer case subframe and skid.
definitely not! Lol Im trying to keep everything on this build as simple as possible.
Not gonna build another set of billet ones like mine
-
- Posts: 292
- Joined: Wed Aug 11, 2010 7:25 pm
- Bronco Info: 1991 351. lightweight special
Re: 95 Black Bronco
Lol Just take the rear steer out of the link setup Cho. I think that would probably suck on a short wheelbase.
-
- Posts: 292
- Joined: Wed Aug 11, 2010 7:25 pm
- Bronco Info: 1991 351. lightweight special
Re: 95 Black Bronco
Sorry RMC I was not chuckling at you, I've just had a few conversations with Mr. Cho
- tcm glx
- Peanut Butter
- Posts: 7303
- Joined: Tue Dec 08, 2009 11:19 am
- Bronco Info: 93 Ford Bronco 5.8
- Location: Riverside Ca
- Contact:
Re: 95 Black Bronco
Rmc wrote:Tony stop jumping on the band wagon. I asked he said yessir and I moved on. Mr cox chuckled about me even asking and Brian acted as though I should expect nothing less. First off I've never met the guy, second why is that you guys think I should have guessed that he would put a new dress on the pig as well as lipstick. I don't know cho his reputation or his history. So remind me agian why I would have known. It's not a stupid question, Stop acting as though it is.
Sorry, I didn't mean to poke.. and I don't know if there is a backdrop to this. I just read what was posted on this thread.
- yikes
- Founder
- Posts: 4138
- Joined: Sun Dec 06, 2009 7:51 am
- Bronco Info: 1996 with tires and stuff
- Location: Yucaipa, CA
Re: 95 Black Bronco
***End drama*** Back to our regularly scheduled program.
CHO! Hurry up and post more pictures. We can't handle too much dialogue or we turn RDC purple.
CHO! Hurry up and post more pictures. We can't handle too much dialogue or we turn RDC purple.
-
- Posts: 21
- Joined: Wed Jan 08, 2014 10:40 pm
- Bronco Info: 93 bronco building using giant motorsports parts and my garage fab skills. family wagon prerunner
Re: 95 Black Bronco
where are the updates Cho? And what about a thread from Johnny?
Re: 95 Black Bronco
Tons of updates recently, got the truck street worthy about a month ago, took it to ocotillo for halloween, still waiting for my glass to be finished at paint. Getting started on linking it now. I ended up getting a camburg full floater, and King 3.0 coilovers with compression adjusters. I will be doing a simple 4 bar 4 link with shock off of the axle with a 3" frame notch, aiming for 22" of travel.