Full Build Bronco 550HP

Dan88Rigid · Post by **Dan88Rigid** » Wed Nov 21, 2012 11:00 am

cs_drums wrote:What calipers are you running? What hubs, rotors and calipers are going up front?

Running the new Jamar Calipers front and rear. One of the best Calipers ive seen so far. Not sure as for hubs. Probably run the stock one for now and stock performance rotor and just the Jamar caliper up front. Theres nothing wrong with the stock hub or rotors

BDKW1 · Post by **BDKW1** » Wed Nov 21, 2012 8:21 pm

Jamars, a step above CNC's, somewhere below Wilwoods, Brembos and Performance frictions.......

Dan88Rigid · Post by **Dan88Rigid** » Thu Nov 22, 2012 6:28 pm

BDKW1 wrote:Jamars, a step above CNC's, somewhere below Wilwoods, Brembos and Performance frictions.......

I beg to differ you probably havent checked out or seen there new racing program and products. Householder Motorsports, Mikey Childress, Green Army, Letner Racing, Cops Racing, and Chase Motorsports all run them and finish in the top 5 in just about every race with no problems should show the quality and how good they are.

BDKW1 · Post by **BDKW1** » Thu Nov 22, 2012 11:43 pm

I have seen them. They are slightly better than CNC's. There is nothing in there desigh which points to any FEA testing or other cool research and development. They do not have dust seals like higher end Wilwoods or other trick features found on other top name calipers. Tell Me how they are better. Show Me deflection graphs under pressure. Show Me braking torque figures. Until I see those with better results than other calipers I will not be impressed. Where is NTSQD when you need brake analysis......

CNC's are about the most stone age calipers out there. It was basically, mill away everything that doesn't fit inside the rim and call it good. There is no engineering in them at all. They just didn't break in half so they became the off-road standard. Monkey see, monkey do. Which is what I'm seeing from the Jamar guys. lots of good talk, little in the way of facts.

cs_drums · Post by **cs_drums** » Fri Nov 23, 2012 8:21 pm

How is the price comparison?

Firetwig · Post by **Firetwig** » Thu Dec 20, 2012 12:58 am

Loving the LS build man.

Dan88Rigid · Post by **Dan88Rigid** » Fri Jan 04, 2013 7:58 pm

Motor, Th400, and NP205 transfer case being installed.

: photo(13).JPG (207.13 KiB) Viewed 1668 times

: photo(14).JPG (161.57 KiB) Viewed 1668 times

economig · Post by **economig** » Sat Jan 05, 2013 2:13 am

Nice Dan!

This thing is gonna scream.

Dan88Rigid · Post by **Dan88Rigid** » Sat Jan 05, 2013 10:50 am

Thanks i hope to have it ready for San Felipe 250 but its gonna be close.

Dan88Rigid · Post by **Dan88Rigid** » Wed Jan 23, 2013 9:59 pm

The motor is off to the builder. Expecting to get 550-580HP out of the motor on pump gas.

D1cker1 · Post by **D1cker1** » Wed Jan 23, 2013 10:22 pm

Do you have any pictures of the interior?

Dan88Rigid · Post by **Dan88Rigid** » Sun Jan 27, 2013 4:51 pm

D1cker1 wrote:Do you have any pictures of the interior?

As of right now i dont. Im on the road working so i will try and have the builder take some. The only thing installed is the dash for right now. Center console to be built soon.

Dan88Rigid · Post by **Dan88Rigid** » Mon Feb 04, 2013 10:32 pm

Mounting up some Rigid Lights!!!

: photo(2).JPG (225.24 KiB) Viewed 1409 times

Dan88Rigid · Post by **Dan88Rigid** » Fri Feb 08, 2013 10:38 pm

(2) 30" Rigid E-series bars mounted.

Post by **SteveG** » Sat Feb 09, 2013 8:36 am

You need to put some teeth between those light bars.

hobbyturnedobsession · Sat Feb 09, 2013 8:44 am

Hahaha that would be awesome!

Dan88Rigid · Post by **Dan88Rigid** » Tue Feb 12, 2013 10:07 pm

SteveG wrote:You need to put some teeth between those light bars.

I will get some white covers and outline the teeth on the covers.

Tanner287 · Post by **Tanner287** » Sat Apr 27, 2013 8:55 pm

Hey is mcniel not sellin this rear glass anymore?? Or do you have to call to order it? I really like it just didnt see it on their website

cs_drums · Post by **cs_drums** » Sun Apr 28, 2013 3:02 pm

Not on there website but still available. Just picked mine up a month ago

Tanner287 · Post by **Tanner287** » Sun Apr 28, 2013 5:54 pm

How much wider is your rear end then stock? Just curious to see how the glass would fit my bronco since it seems like it fits your great. I'm 4" over each side in the rear plus 37s

Full Build Bronco 550HP

Re: Full Build Bronco LS1

Re: Full Build Bronco LS1

Re: Full Build Bronco LS1

Re: Full Build Bronco LS1

Re: Full Build Bronco LS1

Re: Full Build Bronco LS1

Re: Full Build Bronco LS1

Re: Full Build Bronco LS1

Re: Full Build Bronco LS1

Re: Full Build Bronco 550HP

Re: Full Build Bronco 550HP

Re: Full Build Bronco 550HP

Re: Full Build Bronco 550HP

Re: Full Build Bronco 550HP

Re: Full Build Bronco 550HP

Re: Full Build Bronco 550HP

Re: Full Build Bronco 550HP

Re: Full Build Bronco 550HP

Re: Full Build Bronco 550HP

Re: Full Build Bronco 550HP