Page 30 of 30
Re: Andy J's 1995 xlt
Posted: Mon Mar 08, 2021 2:00 pm
by Andy Jones
Hillbilly Heaven wrote:How did you mount your Quick 4 controller? There is a guy in one of the 6R80 groups that is 3D printing flush mounts for the Quick 6. It might work for the Quick 4.
Mine is flush mounted. All you do is take the face plate off and mount it where you like. It’s sandwiched between your cut out.
Sent from my iPhone using Tapatalk
Re: Andy J's 1995 xlt
Posted: Mon Mar 08, 2021 2:15 pm
by Hillbilly Heaven
Andy Jones wrote: ↑Mon Mar 08, 2021 2:00 pm
Mine is flush mounted. All you do is take the face plate off and mount it where you like. It’s sandwiched between your cut out.
Sent from my iPhone using Tapatalk
Thanks I went 6R80. I will have to check that out when i get my controller.
Re: Andy J's 1995 xlt
Posted: Mon Mar 08, 2021 8:09 pm
by Andy Jones
Hillbilly Heaven wrote:Andy Jones wrote: ↑Mon Mar 08, 2021 2:00 pm
Mine is flush mounted. All you do is take the face plate off and mount it where you like. It’s sandwiched between your cut out.
Sent from my iPhone using Tapatalk
Thanks I went 6R80. I will have to check that out when i get my controller.
Nice! Yeah, the quick 4 and 6 are the same shape.
Sent from my iPhone using Tapatalk
Re: Andy J's 1995 xlt
Posted: Sat Apr 17, 2021 1:29 pm
by Andy Jones
Some updates!
Recessed Holley 7 inch dash. Back plate is carbon fiber.
Truck should have been done and wrapped up last weekend.. but.. the brand new transmission that I had built didn’t have any forward gears..
Intake setup.
Need to finish the rear cross bar on the engine cage still.
Sent from my iPhone using Tapatalk
Re: Andy J's 1995 xlt
Posted: Mon Apr 19, 2021 2:14 pm
by Pickuptrucker
sick looking engine bay
Re: Andy J's 1995 xlt
Posted: Tue Apr 20, 2021 7:09 pm
by Andy Jones
Pickuptrucker wrote:sick looking engine bay
Thank you! Still need to clean up some of the wiring, and finish my engine cage.
Sent from my iPhone using Tapatalk
Re: Andy J's 1995 xlt
Posted: Fri May 07, 2021 4:02 pm
by Andy Jones
Here’s a semi better dash pic.
Sent from my iPhone using Tapatalk
Re: Andy J's 1995 xlt
Posted: Mon May 10, 2021 3:24 pm
by Wcbmustang
Woah now, I need to rethink my plans here. Which sniper are you running that will communicate to the digital dash? I’m fixing to sniper swap mine and thought that wouldn’t work. Super nice trick by the way!
Sent from my iPhone using Tapatalk
Re: Andy J's 1995 xlt
Posted: Mon May 10, 2021 7:24 pm
by Andy Jones
Holley Sniper
Part Number 550-511
Sent from my iPhone using Tapatalk
Re: Andy J's 1995 xlt
Posted: Mon May 10, 2021 7:35 pm
by Wcbmustang
Thanks, I guess I need to keep up with Holley updates more often.
Sent from my iPhone using Tapatalk
Re: Andy J's 1995 xlt
Posted: Thu Jun 17, 2021 10:27 am
by Andy Jones
Put some new shoes on the Bronco. Running the 37” BFG KM3’s now!
Sent from my iPhone using Tapatalk
Re: Andy J's 1995 xlt
Posted: Thu Jun 17, 2021 5:45 pm
by hobbyturnedobsession
Alright you’re keeping it right? Its looking good bud. How’s everything holding up now that you’ve been putting it theough the paces?
Re: Andy J's 1995 xlt
Posted: Fri Jun 18, 2021 6:46 pm
by Andy Jones
hobbyturnedobsession wrote:Alright you’re keeping it right? Its looking good bud. How’s everything holding up now that you’ve been putting it theough the paces?
Yessir! Thank You.
Gonna keep it and update/upgrade some stuff.
She’s killing it with the new motor, transmission, and electronics. It’s a totally different animal now!
Sent from my iPhone using Tapatalk
Re: Andy J's 1995 xlt
Posted: Sun Jul 17, 2022 11:00 am
by Andy Jones
Some Nuclear Unicorn updates.
New Camburg full floater housing being built.
Re: Andy J's 1995 xlt
Posted: Sun Jul 17, 2022 1:52 pm
by Wrightracing.net
On my 72 Bronco Project I need to figure out where to put the Holley display for the Terminator. I like your, but the 72 dash does not have room above the steering wheel. Also, I want to keep the dash minimal and clean. I may do it in the center console.
Looking really nice and love the axle, eventually I want to go full floater but I will have to build it myself. I have a Currie 9+ with a truss, but it has only 3.0" tubes and 31 spline. With the new 427, i need to upgrade and sell my current one to help fund a dana 60 snouts version 72 inches while. Now it is 65"
Good luck, you are doing a great job
Re: Andy J's 1995 xlt
Posted: Sun Jul 17, 2022 2:54 pm
by Andy Jones
Thank you!
This new housing will be 71” WMS to WMS. The current one is only 68.5 WMS to WMS. I'll be filling in the rear a bit more so that it'll look more proportioned out back. Basically filling out the rear glass. It's a 3.5” housing and I'm running 40 spline axles.
Re: Andy J's 1995 xlt
Posted: Mon Jul 18, 2022 7:25 am
by toddz69
Nice!! Wasn't your truck on RDC for sale just a few months ago? I'm guessing this means you're going to keep it - good!
Todd Z.
Re: Andy J's 1995 xlt
Posted: Mon Jul 18, 2022 9:08 am
by Andy Jones
toddz69 wrote: ↑Mon Jul 18, 2022 7:25 am
Nice!! Wasn't your truck on RDC for sale just a few months ago? I'm guessing this means you're going to keep it - good!
Todd Z.
Yessir! Lol.
My wife and kids really enjoy the Bronco, as do I! I decided it was time to update a few things and keep shredding on it!
Re: Andy J's 1995 xlt
Posted: Tue Sep 12, 2023 6:06 pm
by HB2BAJA
Where did you get the master cylinder relocation bracket?
Re: Andy J's 1995 xlt
Posted: Tue Sep 12, 2023 6:18 pm
by Andy Jones
Richer Racing/OchoFab
