Page 23 of 30

Andy J's 1995 xlt

Posted: Sat Jul 22, 2017 11:33 am
by cs_drums
Haha that seems a little less time consuming that doing it from scratch! Looking good!!


Sent from my iPhone using Tapatalk

Andy J's 1995 xlt

Posted: Sat Jul 22, 2017 3:38 pm
by Andy Jones
It definitely was! And thank you!


Sent from my iPhone using Tapatalk

Re: Andy J's 1995 xlt

Posted: Sat Jul 22, 2017 7:38 pm
by LvSteve
Looks great, any photos of the a pillar area at the dash ?

Andy J's 1995 xlt

Posted: Sun Jul 23, 2017 4:52 pm
by Tchajagos
tcinu2 wrote:Looks great, any photos of the a pillar area at the dash ?
I have some from another truck.

Image
Image

Re: Andy J's 1995 xlt

Posted: Mon Jul 24, 2017 5:47 am
by LvSteve
Is that 1.75 tubing ? Any ac vent ducting mods. Photos of A - B piller floor area and frame mounting, Thanks guys

Andy J's 1995 xlt

Posted: Sat Aug 12, 2017 11:08 am
by Andy Jones
Finished that main tube structure of the Solo Cage install. Gonna order some material, and start the cab and cab cage to cab plating.
The STOKE is real over here !!
Image
Image
Image
Image
Still thinking about selling my rear fullfloater. Any interest, hit me up! I'll give you the details as to what comes with it.


Sent from my iPhone using Tapatalk

Andy J's 1995 xlt

Posted: Sun Oct 15, 2017 2:57 pm
by Andy Jones
Got the #nuclearunicorn on her own weight last night! She's not the Baddest Bronco ever built. But she's gonna give myself and my family some epic trips! I can finally see the light at the end of the tunnel.
Image


Sent from my iPhone using Tapatalk

Andy J's 1995 xlt

Posted: Mon Oct 16, 2017 8:27 am
by Bajaluv
Andy Jones wrote:Got the #nuclearunicorn on her own weight last night! She's not the Baddest Bronco ever built. But she's gonna give myself and my family some epic trips! I can finally see the light at the end of the tunnel.
Image


Sent from my iPhone using Tapatalk

Right on !!! Getting so close


Sent from my iPhone using Tapatalk Pro

Andy J's 1995 xlt

Posted: Mon Oct 16, 2017 12:49 pm
by Andy Jones
I’m getting antsy!


Sent from my iPhone using Tapatalk

Andy J's 1995 xlt

Posted: Sun Oct 22, 2017 9:21 am
by Andy Jones
Finished up some tube fender mounts. Made the core support a bit sturdier as well. Now I gotta figure out how I’m going to mount all these wires and fuse box !
Image
Image
Purchased one of these as well.
Image


Sent from my iPhone using Tapatalk


Sent from my iPhone using Tapatalk

Andy J's 1995 xlt

Posted: Sat Nov 11, 2017 7:22 pm
by Andy Jones
Few beads I️ laid down. Getting the hang of Mig welding again. Cage is 100% welded finally!

Image

And I️ sweet pic of my baby!
Image


Sent from my iPhone using Tapatalk

Andy J's 1995 xlt

Posted: Sat Nov 18, 2017 9:33 am
by Andy Jones
Picked up a set of Solo Motorsports front air bump mounts and seat slider mounts today!
4hrs from start to finish. Super stoked on these mounts. Gonna order up the bump stops, and a mock up seat this week.
Big props to Bobby and Paul, for all their help, and great customer services! Those guys, and the whole crew at Solo kick ass!!
Image
Image


Sent from my iPhone using Tapatalk

Andy J's 1995 xlt

Posted: Mon Nov 20, 2017 6:24 pm
by Andy Jones
Welded one of my bed plates in today after work. Ran outta gas, so I couldn’t finish the lower section or start on the passenger side.

Image


Sent from my iPhone using Tapatalk

Andy J's 1995 xlt

Posted: Wed Nov 22, 2017 9:54 pm
by Andy Jones
Finished my rear bed plates, and cut a rear fuel pump access panel.
Image
Image
Image


Sent from my iPhone using Tapatalk

Andy J's 1995 xlt

Posted: Sat Nov 25, 2017 5:44 pm
by Andy Jones
Picked up my @kingshocks hydraulic bump stops today. Super excited that the front end of this beast is almost complete. Only small odds and ends left, and I’ll be rippin in the desert!
Image
Image
Image
Image


Sent from my iPhone using Tapatalk

Re: Andy J's 1995 xlt

Posted: Sun Nov 26, 2017 1:37 pm
by Cactus Cooler
Looking good! Was wondering if you had a picture of where the bump meets the TTBs? I have the same Threat beams and was thinking of doing the solo bump mounts, however was also thinking of making the Threat beams a J arm style like Richers. I'm just curious where it picks it up? ( the bump)

Re: Andy J's 1995 xlt

Posted: Sun Nov 26, 2017 2:32 pm
by zachwabbit
Dude this things rad! Can't wait to see the finished product

Andy J's 1995 xlt

Posted: Sun Nov 26, 2017 6:43 pm
by Andy Jones
Cactus Cooler wrote:Looking good! Was wondering if you had a picture of where the bump meets the TTBs? I have the same Threat beams and was thinking of doing the solo bump mounts, however was also thinking of making the Threat beams a J arm style like Richers. I'm just curious where it picks it up? ( the bump)
I’ll try and get something up this week, so everyone can see.



Sent from my iPhone using Tapatalk

Andy J's 1995 xlt

Posted: Sun Nov 26, 2017 6:43 pm
by Andy Jones
zachwabbit wrote:Dude this things rad! Can't wait to see the finished product
Thank you!
Me too! Lol.


Sent from my iPhone using Tapatalk

Andy J's 1995 xlt

Posted: Sat Dec 02, 2017 4:58 pm
by Andy Jones
Got one of my fenders mounted today. Shit was fucking hard!! Pumped on the outcome though.
Image
Image
Image
Image
Image
Image


Sent from my iPhone using Tapatalk