Andy J's 1995 xlt

[Andy Jones]

How did you mount your Quick 4 controller? There is a guy in one of the 6R80 groups that is 3D printing flush mounts for the Quick 6. It might work for the Quick 4.

Mine is flush mounted. All you do is take the face plate off and mount it where you like. It’s sandwiched between your cut out.


Sent from my iPhone using Tapatalk

[Hillbilly Heaven]

Mine is flush mounted. All you do is take the face plate off and mount it where you like. It’s sandwiched between your cut out.


Sent from my iPhone using Tapatalk

Thanks I went 6R80. I will have to check that out when i get my controller.

[Andy Jones]

Mine is flush mounted. All you do is take the face plate off and mount it where you like. It’s sandwiched between your cut out.


Sent from my iPhone using Tapatalk

Thanks I went 6R80. I will have to check that out when i get my controller.

Nice! Yeah, the quick 4 and 6 are the same shape.


Sent from my iPhone using Tapatalk

[Andy Jones]

Some updates!
Recessed Holley 7 inch dash. Back plate is carbon fiber.




Truck should have been done and wrapped up last weekend.. but.. the brand new transmission that I had built didn’t have any forward gears..

Intake setup.

Need to finish the rear cross bar on the engine cage still.


Sent from my iPhone using Tapatalk

[Pickuptrucker]

sick looking engine bay

[Andy Jones]

sick looking engine bay

Thank you! Still need to clean up some of the wiring, and finish my engine cage.


Sent from my iPhone using Tapatalk

[Andy Jones]

Here’s a semi better dash pic.




Sent from my iPhone using Tapatalk

[Wcbmustang]

Woah now, I need to rethink my plans here. Which sniper are you running that will communicate to the digital dash? I’m fixing to sniper swap mine and thought that wouldn’t work. Super nice trick by the way!


Sent from my iPhone using Tapatalk

[Andy Jones]

Holley Sniper
Part Number 550-511


Sent from my iPhone using Tapatalk

[Wcbmustang]

Thanks, I guess I need to keep up with Holley updates more often.


Sent from my iPhone using Tapatalk

[Andy Jones]

Put some new shoes on the Bronco. Running the 37” BFG KM3’s now!





Sent from my iPhone using Tapatalk

[hobbyturnedobsession]

Alright you’re keeping it right? Its looking good bud. How’s everything holding up now that you’ve been putting it theough the paces?

[Andy Jones]

Alright you’re keeping it right? Its looking good bud. How’s everything holding up now that you’ve been putting it theough the paces?

Yessir! Thank You.
Gonna keep it and update/upgrade some stuff.
She’s killing it with the new motor, transmission, and electronics. It’s a totally different animal now!


Sent from my iPhone using Tapatalk

[Andy Jones]

Some Nuclear Unicorn updates.
New Camburg full floater housing being built.

[Wrightracing.net]

On my 72 Bronco Project I need to figure out where to put the Holley display for the Terminator. I like your, but the 72 dash does not have room above the steering wheel. Also, I want to keep the dash minimal and clean. I may do it in the center console.

Looking really nice and love the axle, eventually I want to go full floater but I will have to build it myself. I have a Currie 9+ with a truss, but it has only 3.0" tubes and 31 spline. With the new 427, i need to upgrade and sell my current one to help fund a dana 60 snouts version 72 inches while. Now it is 65"

Good luck, you are doing a great job

[Andy Jones]

Thank you!

This new housing will be 71” WMS to WMS. The current one is only 68.5 WMS to WMS. I'll be filling in the rear a bit more so that it'll look more proportioned out back. Basically filling out the rear glass. It's a 3.5” housing and I'm running 40 spline axles.

[toddz69]

Nice!! Wasn't your truck on RDC for sale just a few months ago? I'm guessing this means you're going to keep it - good!

Todd Z.

[Andy Jones]

Nice!! Wasn't your truck on RDC for sale just a few months ago? I'm guessing this means you're going to keep it - good!

Todd Z.

Yessir! Lol.
My wife and kids really enjoy the Bronco, as do I! I decided it was time to update a few things and keep shredding on it!

[HB2BAJA]

Where did you get the master cylinder relocation bracket?

[Andy Jones]

Richer Racing/OchoFab