Bronco and 9,000 to spend

robertcrav · Post by **robertcrav** » Sat Aug 10, 2013 4:52 pm

Looks badass Drew!!

Who did the bumper?

Drew · Post by **Drew** » Sun Aug 11, 2013 8:51 am

A buddy of mine in Hemet owns a fab shop Total fabrication. He's good and charges a fair price.

Andy Jones · Post by **Andy Jones** » Sun Aug 11, 2013 12:54 pm

Drew wrote:A buddy of mine in Hemet owns a fab shop Total fabrication. He's good and charges a fair price.

Your Bronco, does look Good !.

tcm glx · Post by **tcm glx** » Sun Aug 11, 2013 1:07 pm

Is that a 12" coilover with a 14" bypass? What setup will you run in the rear?

Drew · Post by **Drew** » Sun Aug 11, 2013 9:41 pm

In the front yes. The rear I did Q80's with a 12inch bypass

Drew · Post by **Drew** » Sun Aug 11, 2013 9:42 pm

Thanks Andy

Drew · Post by **Drew** » Sun Aug 11, 2013 10:57 pm

PRP seats on the way. Inner fenders Monday start on the Rollcage and back bumper. Exhaust almost done.

Drew · Post by **Drew** » Mon Aug 12, 2013 9:57 pm

: ImageUploadedByTapatalk1376369845.455496.jpg (44.16 KiB) Viewed 731 times

Drew · Post by **Drew** » Mon Aug 12, 2013 9:58 pm

: ImageUploadedByTapatalk1376369886.933282.jpg (43.39 KiB) Viewed 730 times

Drew · Post by **Drew** » Mon Aug 12, 2013 9:58 pm

Bumper done. Roll cage or inner fenders next.

Kel Fab Creations · Post by **Kel Fab Creations** » Tue Aug 13, 2013 6:48 am

I really like that southwest front setup! Is all the work getting done at total fab?

Drew · Post by **Drew** » Tue Aug 13, 2013 7:37 am

Ya almost done.

robertcrav · Post by **robertcrav** » Tue Aug 13, 2013 8:29 am

Drew wrote:
ImageUploadedByTapatalk1376369886.933282.jpg

Bumper looks good, is it rectangular tube or c-channel?

Drew · Post by **Drew** » Tue Aug 13, 2013 8:40 am

Drew · Post by **Drew** » Wed Aug 14, 2013 7:02 am

Just found out the damn rear end tube is bent. I have a body shop that says we can stick it on a frame machine and tweak it. Hope that will work!!!

Rmc · Post by **Rmc** » Sat Aug 17, 2013 1:05 am

Remove everything to bare housing, find a straight unbent piece of tubing the same o.d. as the I.d. of the housing flanges. Try to pass it through flange to flange. If it won't go it's bent, depending on how bad you can heat the bent area with a rose bud oxy aceteline tip then quench the cherried area to have the housing shrink toward the quickly cooled direction. Repeat the process until its straight enough to pass a bar through. If its really bad a big ass press is the only way. Good luck hope it helps.

Drew · Post by **Drew** » Sat Aug 17, 2013 8:24 am

Thanks going to get if finished then deal with that issue. Was going to have a buddy with a farme machine look at it. But will try your method. I have an induction heater that would work great for that.

robertcrav · Post by **robertcrav** » Wed Sep 04, 2013 7:07 am

Any updates Drew?

Drew · Post by **Drew** » Wed Sep 04, 2013 9:14 pm

Drew · Post by **Drew** » Wed Sep 04, 2013 9:17 pm

http://s852.photobucket.com/user/allena ... sort=1&o=9

Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend

Re: Bronco and 9,000 to spend