Page 18 of 18
Re: 95 Black Bronco
Posted: Wed Nov 18, 2015 12:40 am
by Rmc
Might want to look at power steering solutions and Psc. Psc has a full kit for much less than Howe. Not real sure how high the quality is though but it's a big seller with the jeep crowd. Might be worth looking into.
Re: 95 Black Bronco
Posted: Wed Nov 18, 2015 5:46 pm
by motoxscott
Charlie @ PSS is good .... stay away from PSC. Had some friends get their stuff and wasn't happy with the quality compared to Lee, Howe, PSS.
- Scott
95 Black Bronco
Posted: Wed Nov 18, 2015 9:27 pm
by C H O
Talked to Bobby at solo the other day, he was super helpful. Think im going to run their setup using a rebuilt ported box, Howe t/c pump, resevoir with filter, pulley and cooler.
Re: 95 Black Bronco
Posted: Thu Nov 19, 2015 12:22 am
by Rmc
Can't go wrong with Howe.
Re: 95 Black Bronco
Posted: Thu Nov 19, 2015 7:00 am
by hollandermotorsports
C H O wrote:Talked to Bobby at solo the other day, he was super helpful. Think im going to run their setup using a rebuilt ported box, Howe t/c pump, resevoir with filter, pulley and cooler.
Good choice buddy.
Re: 95 Black Bronco
Posted: Thu Nov 19, 2015 10:10 am
by zachwabbit
Dang dude that rear bumper is clean!! Hoping to have something similar made for mine soon
95 Black Bronco
Posted: Thu Dec 03, 2015 9:15 pm
by C H O
Some goodies!
Re: 95 Black Bronco
Posted: Thu Dec 03, 2015 9:31 pm
by SteveG
Bad. Ass. Looking damn good!
Re: 95 Black Bronco
Posted: Thu Dec 03, 2015 9:58 pm
by dtbback
That center console is beautiful!!! How did you make it?
95 Black Bronco
Posted: Thu Dec 03, 2015 10:41 pm
by C H O
Curt at crb built it, it is blended aluminum, same one that was in Gary's red bronco
95 Black Bronco
Posted: Fri Dec 04, 2015 7:43 am
by cs_drums
So tight!!!
Re: 95 Black Bronco
Posted: Sat Dec 05, 2015 6:56 am
by cbw
always impressed with your work cho.
95 Black Bronco
Posted: Sat Mar 19, 2016 8:38 pm
by C H O
Re: 95 Black Bronco
Posted: Sun Mar 20, 2016 10:58 pm
by keenanduran1
sexxx
Re: 95 Black Bronco
Posted: Tue Mar 22, 2016 12:01 pm
by Seabass
Did you have the stops added in the box?
Re: 95 Black Bronco
Posted: Wed Jun 15, 2016 1:41 pm
by dtbback
C H O wrote:Got a bunch to tubes done today, got the cage all tacked up and slid it out the back to weld an paint. Still have to to do corner gussets and window v tubes. The cage is 2" and 1.75" fully tig welded, goes through the firewall in 4 spots, fully sealed, stock dash and stock headliner. My seats should be done in a week stoked to see it taking shape!
ImageUploadedByTapatalk1394926443.737621.jpg
Hey Cho,
What diameter is the A-pillar cross tube?
Re: 95 Black Bronco
Posted: Wed Oct 05, 2016 9:20 am
by carlover
What rear spring rate did you end up with? I'm looking into building a similar setup and need a good starting point for springs.
Re: 95 Black Bronco
Posted: Wed Oct 05, 2016 10:11 am
by De$ertBronco