1994 Bronco for General Tire Media

[cypher]

That is a nice shop! Must be so nice to have a lift like that. Bronco looks the business.

[hollandermotorsports]

Thank you. The lifts are very nice. If any GFB family need to tinker you guys are welcome to use the lift. This is my hobby shop for tinkering on toys. It is located in Vista California.

[hollandermotorsports]

11017484_1015965018431289_4139902179590812438_n.jpg (80.7 KiB) Viewed 1368 times

11037636_1015964831764641_6176960463194309207_n.jpg (75.74 KiB) Viewed 1368 times

11051851_1015964688431322_7663148508470789330_n.jpg (78.88 KiB) Viewed 1368 times

11133741_1015964391764685_168149291863576363_n.jpg (113.75 KiB) Viewed 1368 times

11133741_1015964518431339_5527367876383803615_n.jpg (92.55 KiB) Viewed 1368 times

11137156_1015964738431317_1924210891627576085_n.jpg (66.43 KiB) Viewed 1368 times

As you can see I have been busy plumbing. New Trans is in hoping to drive this week.

[Baja]

Saw this thing first hand on Saturday. Going to be awesome.

[1Hondalover]

Seriously like that axle and those canoe links......good job Richer!

Bobby are you listening?

[hollandermotorsports]

Seriously like that axle and those canoe links......good job Richer!

Bobby are you listening?

Those are Bobby's links and a Camburg housing tabbed and executed by Richer. Between Solo and Richer and Camburg I am beyond stoked with the Bronco.

[hollandermotorsports]

22420_1016487348379056_2831336472970368537_n.jpg (71.19 KiB) Viewed 1292 times

988915_1016487308379060_6220018626498071475_n.jpg (57.83 KiB) Viewed 1292 times

1526561_1016487245045733_8907899310454862356_n.jpg (68.52 KiB) Viewed 1292 times

10632833_1016487265045731_2609471296858498148_n.jpg (64.9 KiB) Viewed 1292 times

10632833_1016487375045720_5406214595058804086_n.jpg (43.13 KiB) Viewed 1292 times

11138527_1016487391712385_3377720879148877269_n.jpg (40.65 KiB) Viewed 1292 times

Installed the new tank last night and as you can see it looks good but it is a little tight with the rear end pushed back.

[hollandermotorsports]

11148670_1016487278379063_5200770701986422309_n.jpg (74.66 KiB) Viewed 1292 times

11159996_1016486608379130_327908042301509854_n.jpg (69.57 KiB) Viewed 1292 times

11026221_1016485751712549_4812461083565550327_n.jpg (73.03 KiB) Viewed 1292 times

11000109_1016487418379049_778764907281308475_n.jpg (89.88 KiB) Viewed 1292 times

18927_1016487441712380_6813285744811582788_n.jpg (158.73 KiB) Viewed 1292 times

My new water pump also came in. I accidentally ordered an extra thermostat if any one is looking for one.

[ChaseTruck754]

Damn - that rear end at the tank does look TIGHT!

[BajaBronco13]

Is that a Northwest 45 gallon tank?

Chris

[cs_drums]

I wouldn't worry, take it down a rough section it will self clearance. Just watch that breadline.

[hollandermotorsports]

Is that a Northwest 45 gallon tank?

Chris

yes it is north west metal products tank.

That was the extreme on the tank. Believe it or not the stock tank and skid plate was closer it needed to be notch to cycle.

[keenanduran1]

How much was the fuel tank?
Did you have any issues on the install?
Is it race legal?

[ChaseTruck754]

Not race legal as it's just a tank, not a cell. He had a thread on here somewhere about doing a group buy or order for them as it seems it would be the last run of them. Maybe that was early on in this thread - can't remember. Seem to think cost was about $600 or so.

[Tanner287]

I think you should just stop now, and trade me broncos ;D

I love the rear end, your making me wish I linked mine

[Tanner287]

Oh and what brand quick release did you buy? And what model is that momo? If you happen to have a link to it post it up
Iv been wanting to do that on mine for a whike

[hollandermotorsports]

How much was the fuel tank?
Did you have any issues on the install?
Is it race legal?

Tank install was easy. Plumbing is the tricky part I'm doing 2 weldon big TT pumps so I am doing some custom tank pick ups. Tank was roughly $700 shipped. As far as being race legal it does not have a bladder so some organizations would allow but Score and BITD would not.

[hollandermotorsports]

Oh and what brand quick release did you buy? And what model is that momo? If you happen to have a link to it post it up
Iv been wanting to do that on mine for a whike

The MOMO wheel is their top of the line suede wheel with horn buttons. For me one will be horn and one will be PTT this is how we set them up in our race trucks. The quick release is a Sweet 6 bolt off the shelf quick release I picked up both at ORW. As far as linking it that's what made the most sense for me. With that said I know many Bronco that work awesome with leafs. Mine had leafs when I bought it but I decided to link due to high off-road miles it will see. Leafs fatigue and crack I do not want to swap leafs in the middle of baja. So it made sense. Your Bronco looks great and seems like it works good.

[Tanner287]

Yeah it works out perfect for me. I wanted to have a fun pre runner and I couldn't shell out all the cash for linking it but maybe in the future. For now it does great for me!
Once this things all done Id love to make a trip with a bunch of people and get to ride in this to see how it is.

[hollandermotorsports]

22827_1021820294512428_7089605546445307715_n.jpg (79.07 KiB) Viewed 1039 times

1560442_1021820457845745_2695664746724005769_n.jpg (76.85 KiB) Viewed 1039 times

11145190_1021820194512438_8069498103206639421_n.jpg (104.15 KiB) Viewed 1039 times

11188168_1021820404512417_7493882469859863138_n.jpg (78.23 KiB) Viewed 1039 times

I know it has been a little while on the updates but now it looks like something.