95 f150 4x4

steve-oh · Post by **steve-oh** » Fri Jul 05, 2013 5:37 am

Travisfab wrote:

You will want to cut out the area in the yellow box. That flange is only needed if you are deleting your radiator core support.

Thanks for the info travis.

steve-oh · Post by **steve-oh** » Fri Jul 05, 2013 5:43 am

Rmc wrote:Not to get too ghetto fabulous on you but quite a few local kids cut the spot welds then press the bed sides out with a 2x4, hold em in place with the 2x4( between frame and inside of bed skin. Then take 1 inch conduit smash the ends flat. Bend it over 90, hold it to the frame mark the other side ( flat) then bend that side to 90 also. Kinda like a cheap brace in the shape of a Z. I'm not saying I would rock it but if buget is super tight 7 to 10 bucks for 3 or 4 tries is ready for race day. It Beats shredded tires anyday. Proving where there's a will theres a way.

Thats my plan, cut the brace from the inside of the wheel well to bed side, put a jack in the push it out as far as i can w/o wrinkling the side, going to practice with the bed thats on there.....thanks for the guidance guys keep it coming

steve-oh · Post by **steve-oh** » Mon Jul 08, 2013 8:32 am

The steering linkage interchanges between 2 & 4 wheel drive if i remember correctly Right?

steve-oh · Post by **steve-oh** » Thu Jul 11, 2013 9:45 am

Dropped off for paint today should be done sunday

ChaseTruck754 · Post by **ChaseTruck754** » Thu Jul 11, 2013 10:14 am

Nice. This thing is progressing quickly!

Rmc · Post by **Rmc** » Thu Jul 11, 2013 10:40 am

Can't wait to see after paint.

steve-oh · Post by **steve-oh** » Thu Jul 11, 2013 12:18 pm

Trying to be driving this thing by next weekend,...still have to swap in front end and fix the a/c, steering linkage should interchange right

steve-oh · Post by **steve-oh** » Fri Jul 12, 2013 10:41 am

Rebuilding front axle today, ball joints, bearings, seals and brakes

steve-oh · Post by **steve-oh** » Fri Jul 12, 2013 10:44 am

After pic

steve-oh · Post by **steve-oh** » Sat Jul 13, 2013 8:25 am

Sand, sand,sand......

tcm glx · Post by **tcm glx** » Sat Jul 13, 2013 9:33 am

Nice work........

Pop the chrome trim around the windshield off.....it just has little clips on it, will help for a better paint job.

steve-oh · Post by **steve-oh** » Sat Jul 13, 2013 5:51 pm

Little sneak peak.....just got it back to shop at home, put it all back together tomorrow and put the front beams in

steve-oh · Post by **steve-oh** » Sat Jul 13, 2013 5:54 pm

Picked up some goodies for another project too while i was out......

steve-oh · Post by **steve-oh** » Sat Jul 13, 2013 6:39 pm

Any chance i could get some dxf cut files for some rear spring hangers and shackles for my laser guy

steve-oh · Post by **steve-oh** » Tue Jul 16, 2013 6:09 pm

Had a set back, wrong ratio in rear end from the frame donor truck, so went ahead and put a e 150 8.8 rear end in, gained 1.5 inches gonna be close with the pulled bedsides

steve-oh · Post by **steve-oh** » Tue Jul 16, 2013 6:16 pm

Probably going to break done and get my own bender too, so thats going to put things behind, but its been long over due. Looking at the model 32 now, was using a friends model 4 and it was sweet but alittle pricey.

steve-oh · Post by **steve-oh** » Wed Jul 17, 2013 5:33 pm

Almost back together....got to build a temporary ft bumper till i get my bender, install my amp, fix ac and we are rolln.

FUFIMI · Post by **FUFIMI** » Wed Jul 17, 2013 6:43 pm

Look really good

ESHALLBETTER · Post by **ESHALLBETTER** » Wed Jul 17, 2013 7:46 pm

Damn, that thing looks gay

ESHALLBETTER · Post by **ESHALLBETTER** » Wed Jul 17, 2013 7:47 pm

Sorry! I'm on my phone! That looks GREAT!

95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4

Re: 95 f150 4x4