White 1994 F-150 Sleeper Build

nubreed71 · Post by **nubreed71** » Tue Jan 05, 2016 1:55 pm

Sounds like I need to put in a call to Mastercraft to see if they'll build me something to match my front seats. Thanks for the info guys!

funinthesun95 · Post by **funinthesun95** » Tue Jan 05, 2016 5:43 pm

what in your ride again?

D1cker1 · Post by **D1cker1** » Tue Jan 05, 2016 8:28 pm

Just curious on the reason for the rear bench seat?
Will there be someone sitting in the rear?

cs_drums · Post by **cs_drums** » Tue Jan 05, 2016 9:34 pm

Nope just for looks

nubreed71 · Post by **nubreed71** » Tue Jan 05, 2016 9:37 pm

This truck does dual duty as my surfmobile, as well as the family beachmobile, so I've gotta be able to get the wife and 2 kids in car seats in there.

RyanDS650X · Post by **RyanDS650X** » Wed Jan 06, 2016 11:05 am

Shoulda bought a Bronco... haha

tcm glx · Post by **tcm glx** » Wed Jan 06, 2016 11:21 am

RyanDS650X wrote:Shoulda bought a Bronco... haha

lol...... Would have already been 4wd and have rear seat room!! ha

nubreed71 · Post by **nubreed71** » Wed Jan 06, 2016 12:54 pm

But almost useless for hauling stuff

keenanduran1 · Post by **keenanduran1** » Wed Jan 06, 2016 10:39 pm

I'll take that shell off you if you get rid of it

nubreed71 · Post by **nubreed71** » Wed Jan 06, 2016 10:56 pm

Will let you know if I do. Right now I'm leaning towards keeping it. Gonna slap a new rubber seal on the underside and through bolt it to the bed rails so that it doesn't move around in the dirt.

nubreed71 · Post by **nubreed71** » Sat Jan 23, 2016 12:20 pm

Went from this:

To this:

And got the fuel pump access panel sprayed as well.

I can't say enough good things about the good folks at LineX San Diego in National City. They knocked this out in a day and made the truck look great. Highly recommend those guys!

cs_drums · Post by **cs_drums** » Sat Jan 23, 2016 12:22 pm

Super clean .... As usual.

dtbback · Post by **dtbback** » Sat Jan 23, 2016 2:13 pm

Very nice detail work!

ChaseTruck754 · Post by **ChaseTruck754** » Mon Jan 25, 2016 10:00 am

Nice! So want to do the inside & underside of the crew bed. LOOOVE the look under the bedsides there

RyanDS650X · Post by **RyanDS650X** » Mon Jan 25, 2016 12:10 pm

What are those fasteners called? Looks great!

tcm glx · Post by **tcm glx** » Mon Jan 25, 2016 12:36 pm

Nutserts

nubreed71 · Post by **nubreed71** » Sun Feb 28, 2016 6:26 pm

The boys over at Richer were able to whip me up a set of bedside supports to finish off the fiberglass install. I had them shot with some LineX to keep em from rusting.

nubreed71 · Post by **nubreed71** » Wed Mar 23, 2016 10:32 am

Swapping on the new 8125 coilovers. Pretty excited about these...1" shorter eye to eye measurement at full compression, so I can drop the ride height a little bit and keep the same amount of bump travel (Once I shorten the bump pads on the radius arms...more about that later).

Yes, I know the coil springs are opposite in direction. For some strange reason Hypercoil winds their heavier rate springs one way, and their lighter weight springs the opposite direction. Go figure.

tcm glx · Post by **tcm glx** » Wed Mar 23, 2016 10:39 am

Your rear fenders painted yet?

nubreed71 · Post by **nubreed71** » Wed Mar 23, 2016 10:42 am

Hahahaha, and so it begins. Gonna be a loooooooong year or so until I finally paint those damn things...lol.