In this case, it is not for racing. I definitely prefer real race radios like the Kenwood TK790H or if on a budget, a TK730H. I own both of those and they both work great, the TK730H is a little more difficult to get programmed, but a computer literate person with Windows XP experience can get it to...

The Switch Pro is basically a solid-state relay. If you wire it properly there should be a power supply directly from the battery. This is the power to supply all your lights and accessories. Then you have the Light Blue wire, which is a ignition sensor trigger wire. It turns the Switch Pro unit on ...

Looking for some Slotted Mag wheels. 16.5x9.75 with 8x6.5 lug pattern. They can have a ruff finish. I plan to have them beadlocked and powder coated. eventually I want to have a set of sand tires for the dunes and a set of hard pack tires. And a couple spares. I will probably have a couple for paddl...

Nice, I have a CT330 stroker motor in my 250r. I completely rebuilt it, split the case's and put a NOS CT top end. I have a 2006 Honda trx450er with a stage 2 hot cam I ride now and love it and electric start is nice now that I am in my 50's. I have too many toy's, I have the 450, a 400ex, a 1990 Y...

I am looking for a set of Early Bronco front Fenders and a hood. They can be ruff. I need them to section in pieces above the wheel wells to extend the Fenders and the hood to widen another hood. I will be lengthing the Fenders around 6 inches and the hood will be widened 6.5" per side of the hood, ...

Hey Guys I have been looking for a all Band All mode radio that will cover 25mhz to 600mhz. Am and fm. I want one with a remote head and 100w. It would go in my 72 Bronco. I want something I can use with mixed groups of CB, Race Radio and UHF guys. I have a Kenwood TK790H and TK890H dual band and a ...

Ok, I found some Spicer 35 spline outer conversion kits with everything but they are listed for a Ford F350 1978-1997 Dana 60 35 Spline Chromoly Outer Axle Shaft Conversion Kit. Do you think they will work on a Dana 50 Hub and knuckle? https://uploads.tapatalk-cdn.com/20240119/5ceac39903b5663d011162...

I like it. Great work, I think Andrew Cho it doing something similar. I do like the idea of getting rid of the ball joints. I wonder what maintenance and the life of the unibals would be on an everyday driver? I would consider uniball rubber dirt and water seals to keep them clean. I have run covers...

Ok, I know you are saying, another post From David [emoji15][emoji24] Ok, the topic is about putting Transmission coolers on the side of a Bronco behind the door behind the quarter panel. I saw Brandon Hollander had vents built into his Bronco quarter panels and he said it was a lot of work. I may b...

I have not tuned my Fox 2.5x16 coilover's with 2.5x16 bypass yet, but I have 400x16, 450x16 and 500x16 springs to choose from. On Chris Wilson's Class 3 Early Bronco with a 1990 chassis under it, Glen ran 500 over 500 with 14 inch shocks and the spring length was 14 inches each, upper and lower. I a...

Love it[emoji106] My plan for now is to look for a set of the old 8 lug 16.5x9.75 aluminum slotted mag wheels. I already run BFG Baja 37X12.50R16.5LT ON my F350 and like them. I can get nos 100% new for $300 each and used 90% tread for $125-150 each. My Bronco is a Off-Road toy and won't see much st...

I know this is a old thread, but I can't sleep and bored. [emoji6] Has anyone used a 08 F350 rear axle. I found a deal on one from a gas truck with 4.10 gears and the factory e-locker for $650 +$150 shipping. It has a 123k miles. I have read on other forums the 05+ axles were better with 35 spline a...

As I am looking for Dana complete knuckles from a 95-97 F250, they are hard to find. I have heard the Dana 60 knuckles should bolt right on. I do want to run the 35 spline outer axles. Has anyone done that swap on the Dana 50 TTB. I like the 1999 Superduty auto hubs with the manual lock backup. It w...

My issue is the Bronco will see mostly sand dunes, so higher RPM'S and tire speed is needed and paddle tires will get used eventually, so that is where torque may come into play I think. I will probably run 37X12.50R Baja TA tires buffed and have Scat Track hauler paddles installed. Probably 8 or 10...

Is there a possibility that you can get an app from Lowrance that turns a tablet/iPad into a GPS- maybe with a wireless gps lowrance style dome antenna ? I’ve posted 2 questions because I want the GPS of the lowrance but I want a bigger turn by turn when I’m needing to find whatever place I need at...

I still run a couple of the old Lowrance 5in mono chromatic GPS. The use the .use files. I got them back in early 2000 and I use to prerun and Mark the MDR courses back then. I always had fun making detailed GPS maps out at Plaster City and in Baja. I was thinking of getting a Garmin USB GPS antenna...

What is a Screw the scam run? I love night runs, but I am in San Diego.

David

https://www.ruggedradios.com/index.php?main_page=product_info&products_id=2923 Can be used for a UHF antenna, too. I put a little stubby antenna on there... looks cool and fills the hole. I really like those antenna mounts. I will be running a Kenwood TK-790H dual band TK-890H radio setup and a hig...

I am thinking about my motor for the Bronco. I am looking for a builder that can either rebuild a 351w with all the proper clearances and upgrades for a 408w stroker. I can source the major parts, but I am not experienced in V8 building. I use to rebuild 2 stroke dirtbike motors growing up. I am goi...

I was wondering if anyone has put a unit bearing knuckle from a F350 to a Dana 50 TTB front axle. I have a 1999 f350 and I like the automatic hub lock, but it still has a manual lock on the hubs. I have Dana 50 beam ends, but I have not welded them in yet. I was wondering if the Superduty knuckles w...