Bumps sold

Yes please!

Was!!! The rust took over and the body was falling off the frame. Just a matter of time till i find another one.

Still have the body panels and bumpers. Those are specialized and doubt ill sell them and dont have the heart to scrap them either. They will remain as wall art untill the time comes that i get another.

Project is dead. No sense beating on it. The rust has literally taken over and its just not worth chipping away at it. The body and frame are headed to the chipper this week.

Sold

Used set of 4.09 reverse rotation ford highpinion gears.

$100 shipped.

Have a used set of 8.8 gears. 5.13 ratio. Also have new minor install kit.

$180 shipped.

Have pair of Fox 2.0 x10" reservoir shocks. Dont know what the valving is. They are the ones with blue annodized ends. Currently discharged of nitrogen. $250 shipped. Have pair of Fox 2.0 x14" reservoir shocks. Again dont know valving. They are older ones. Currently discharged also. $300 shipped Hav...

Not much done that is worth pictures. Got the tcase on the trans and got the axle set on perches. Got it centered. Just need to get engine and trans in to set the pinion angle then i can get the perches tacked on.

I like the simplicity of the disc brakes. That was the reason I went that route years ago. But with limited budget and lots of other areas that need attention I'm thinking disc brakes will take a back burn, on the list of must have things. I doubt I'll have stopping issues with the drums. Just tryin...

Getting my F150 axle (8.8) setup under my BroncoII. Just wondering what your guys thoughts are on the Drum V's Disc. Making a bracket to hold an Explorer caliper isn't a big deal for me. Rotors on the other hand, and I don't care to be sourcing parts from different makes and models. Right now I'm co...

Will be crankin on this this week. See if i can get the motor and trans in place. So i can finish the crossmember. Get the rear axle cleaned up and in place and try to get the front locked down to get radius arms built.

Getting the itch to wrench on this thing again. Picked up an 8.8 from an F150 yesterday. Going to ditch the Expo rear and wheel adapters. The F-150 axle is 1" wider than the Expo+spacers. Time to get the 5.13's and mini spool stuffed into it and get it under the truck. May be moving in the spring so...

Had a feeling I had a boost leak somewhere. As sometimes I would hit 7 PSI but othertimes I would only get 5. Had a feeling that my blowoff was opening too soon and that the boost pressure was opening the valve overcoming the spring pressure. I would get a hiss like it was blowing off before it woul...

Painted the intercooler flat black so it's not obvious any more. http://i128.photobucket.com/albums/p198/Villanmotorsports/VMS%20Ranger/42EDE280-000E-4D04-BA29-29A7F2FE014D-27542-000021995DB7AE62_zps53bb9690.jpg Started working on a water/methanol injection setup. http://i128.photobucket.com/albums/...

I had a spare set of 31's that I made into new whitewalls. There were chunks of rubber missing from the old ones. oops. When I put the turbo motor in I planned to have 4 guages on the top of the dash so I could monitor the vitals. Oil Pressure, Boost, AFR's, and Coolant temp. I mounted them on an al...

Haven't been on here in a while. Have some huge updates. After driving it all winter I was just going to leave it alone but decided I needed to finish my ideas off. I've switched so many different directions on this that I needed to stick to a plan and finish things off. Talking about it doesn't get...

Stakebed rails. http://i128.photobucket.com/albums/p198/Villanmotorsports/VMS%20Ranger/7BE36BD6-41E6-4DFC-94F5-1A5B4BE4DB7A-8897-00000AC0C8C72EFD.jpg http://i128.photobucket.com/albums/p198/Villanmotorsports/VMS%20Ranger/FB804035-6610-40E0-B417-89C421E09935-8897-00000AC0D3BB0F15.jpg http://i128.phot...