Search found 11 matches
- Tue Aug 08, 2017 4:51 pm
- Forum: Non-Broncos
- Topic: 1997 F250 I beams
- Replies: 3
- Views: 582
Re: 1997 F250 I beams
I may want to use it on a 70's long travel setup. I'll cut the whole front clip out of the scrap truck.
- Sat Aug 05, 2017 4:16 pm
- Forum: Non-Broncos
- Topic: 1997 F250 I beams
- Replies: 3
- Views: 582
1997 F250 I beams
I have a set from a 1997 F250 reg cab 8' bed 460 auto built in Mexico 8600 GVWR any good for off roading at speed? I have not pulled them yet so I don't know the exact specs and being on the east coast not much for Baja racers out here to socialize with for info. thanks,
- Sun Jul 05, 2015 9:49 am
- Forum: Race Vehicles
- Topic: Smith Racing 1450 TTB Ranger
- Replies: 42
- Views: 10228
Re: Smith Racing 1450 TTB Ranger
Hauls Assington wrote:Nice.
I am working on my roll cage right now, I wish your brother was down here helping me! I got the A-pillars bent, and b-pillars cut, I have the mounts made, and holes drilled.
What roll cage regulations are you going with?
Nice truck!
- Sat Jun 27, 2015 5:27 pm
- Forum: Race Vehicles
- Topic: MOSS BROTHERS 79 BRONCO CLASS 3 RACER
- Replies: 107
- Views: 44574
Re: MOSS BROTHERS 79 BRONCO CLASS 3 RACER
Hi Moss Brothers, what U joint series do you run in the driveshafts? CV at transfer case?
- Fri Jun 26, 2015 11:21 am
- Forum: Race Vehicles
- Topic: AC box delete on 78\79
- Replies: 2
- Views: 3374
AC box delete on 78\79
I want to get rid of the AC box but keep heat\defrost capability, some suggestions for those have done it.
- Fri Jun 26, 2015 8:22 am
- Forum: Race Vehicles
- Topic: Trans and gear ratio's ?
- Replies: 7
- Views: 4516
Re: Trans and gear ratio's ?
I have the E4OD wide ratio gears, big R-Servo piston and TCI reverse manual shift, TCI torque and shifting is OK. Since I went to 37 the 4:10 gears are really not enough. I just finished my 5:13 gears. Should be putting them in after this winter. I’m sure this will revive the truck! Also, what I ha...
- Wed May 27, 2015 7:40 pm
- Forum: Race Vehicles
- Topic: MOSS BROTHERS 79 BRONCO CLASS 3 RACER
- Replies: 107
- Views: 44574
Re: MOSS BROTHERS 79 BRONCO CLASS 3 RACER
Your transmission (C6 ?) do you use stock clutch drums? with a few mods?
- Tue May 26, 2015 3:19 pm
- Forum: Race Vehicles
- Topic: MOSS BROTHERS 79 BRONCO CLASS 3 RACER
- Replies: 107
- Views: 44574
Re: MOSS BROTHERS 79 BRONCO CLASS 3 RACER
Hey, your trans to transfer case adapter, aluminum or steel?
- Mon Feb 16, 2015 8:37 am
- Forum: Non-Broncos
- Topic: The F-Bomb
- Replies: 289
- Views: 19517
Re: The F-Bomb
Hi F-Bomb, nice build I like the details you put in to it. A couple of questions if have time:
1. Your rear leaf spring mounts\shackles you build them or source them?
2. Front spindle\knuckles Ford 1 ton? Weld them with ER70 Sx wire?
thanks,
-Tom
1. Your rear leaf spring mounts\shackles you build them or source them?
2. Front spindle\knuckles Ford 1 ton? Weld them with ER70 Sx wire?
thanks,
-Tom
- Thu Jan 08, 2015 11:51 am
- Forum: Race Vehicles
- Topic: MOSS BROTHERS 79 BRONCO CLASS 3 RACER
- Replies: 107
- Views: 44574
Re: MOSS BROTHERS 79 BRONCO CLASS 3 RACER
Thanks for sharing, just amazing to see a late 70's Bronc be so competitive two thumbs up to the fabricators, drivers, crew, etc.
I watched a lot of your videos on youtube.
Now my gears are turning
I watched a lot of your videos on youtube.
Now my gears are turning
- Sat Jan 03, 2015 6:09 pm
- Forum: Race Vehicles
- Topic: MOSS BROTHERS 79 BRONCO CLASS 3 RACER
- Replies: 107
- Views: 44574
Re: MOSS BROTHERS 79 BRONCO CLASS 3 RACER
Newbie here, thanks for letting me in.
A couple of questions on the Moss Bronc
-any boxing added to the frame?
-rear leaf spring hangers who made them?
A couple of questions on the Moss Bronc
-any boxing added to the frame?
-rear leaf spring hangers who made them?