-JD5353- wrote:You can have mine. If your not local I'll send them to you for the cost of a flat rate box.

I deffently will take you up on that I will send a pm you when I get home.

The front lower mounts on both my Broncos were broken when I bought them. I veed out the cracks and welded then welded a nice bead all around the large stud base. Has held up fine for 130K miles including one Vegas to Reno Prerun. Make sure that front shock isn't acting as your bump stop or limit s...

Both of my aux shock lower mounts are bent. One is also cracking I was wanting to know if there is any good options for replacing them? Aftermarket sources? Or should i just locate new OEM mounts and keep a eye on them? The truck had not been maintained and was abused before I got it so repairing ev...

Just a update the passenger beam bracket was bent. Replaced them along with all the bushings and driving way better last thing I need to do is wheel bearings then shocks. I can't afford c&t as much as I want to. So going to build this up the best I can with brackets and going to be keeping it at 6" ...

I can't remember, but doesn't the superlift brackets have 2 sets of holes to go 6" or 4"? If so, Get some 4" coils, ditch the 2' block, put some bilstein 5100's on and go have fun! The stock leafs really aren't that bad if you aren't pushing it real hard. Yes i do have 2 sets of holes. The reason i...

I can't remember, but doesn't the superlift brackets have 2 sets of holes to go 6" or 4"? If so, Get some 4" coils, ditch the 2' block, put some bilstein 5100's on and go have fun! The stock leafs really aren't that bad if you aren't pushing it real hard. Yes i do have 2 sets of holes. The reason i...

My bronco has a 6" lift going for a cheap all around rig. A lot of unmaintained roads fire roads ect. And also a lot of mud and really deep ruts. Not worried about jumping but it will be taking some big hits from ruts and holes in the unmaintained roads. Going to be running Doetsch Tech Pre-runner 8...

Anyone of a 6" lift they could compair this too?

http://i231.photobucket.com/albums/ee226/tcfairlane/Mobile%20Uploads/IMG_20140713_205327301.jpg Is this bent or are they made this way? I have a major hunch this is the cause of a few issues I am having including the passenger side axle rubbing on the Axel beam. Next question is on repaits . is it ...

Pretty sure shipping to Texas would be pretty high non oncl here though going to pull one at a hard. And never said anything about a shop I do all my own work.

I have looked at them at solo and camburg are there any "Cheaper" Options out there?

Good core* on my phone... Lol

I don't have the money it's not a matter of biting the bullet with a good acre its still around 1500 forthe beams I have found. I do not have a food core and i can't pull mine and have it shipped off for so.done to do the work I need the truck. I wish i could just drop the cash and have a good cut a...

I was not sure what I was suggesting just brain storming the main point was if there were ways to repair it the beams would get pulled if so I would do the cut and turn while it was out. If using a press would I just try to get the clearance back by bacicaly beding it back? How would I make sure eve...

Would i be able to correct this the same way you do a cut in turn (As in Can i Do a cut and turn and correct the bend at the same time and reinforce everything)

Texas but thanks for the offer lol

I guess the next step is to find another one to compare it with... Pretty sure this is my issue or at least part off it it deffently has some wrinkle to it

I just went out there and looked at that exact spot Aussie and i think that might be my issue.. Should that whole bottom section of the beam (The flat part of the metal) Be a smooth? I Am guessing so and mine has a few waves right in that area.. I do not see any stress marks or anything though could...

Thanks and will do.. Just got a promotion today so hope to have a bit more money for mods... Need to get my Tacoma paid off first though lol

If I had the money I would for sure do c/t beams just not in the budget.. I work till Monday but will for sure dig in to it thanks for helping me figure it out