Search found 163 matches

by monkei
Sat Dec 26, 2015 9:40 pm
Forum: Parts
Topic: New 3503 BBK Ford Bronco F-Series Twin 61mm Performance Throttle Body - $300
Replies: 4
Views: 529

Re: New 3503 BBK Ford Bronco F-Series Twin 61mm Performance Throttle Body - $300

Other things I'd be willing to trade for / trade w/ cash for:

96 bronco signal mirrors (esp. driver's side)
ZF SH-47 5 speed
by monkei
Fri Dec 25, 2015 8:41 pm
Forum: Parts
Topic: New 3503 BBK Ford Bronco F-Series Twin 61mm Performance Throttle Body - $300
Replies: 4
Views: 529

Re: New 3503 BBK Ford Bronco F-Series Twin 61mm Performance Throttle Body - $300

Also willing to entertain trades for EECIV tuning equipment I.E. TwEECer , Moates QH etc.

-Patrick
by monkei
Fri Dec 25, 2015 8:31 pm
Forum: Parts
Topic: New 3503 BBK Ford Bronco F-Series Twin 61mm Performance Throttle Body - $300
Replies: 4
Views: 529

New 3503 BBK Ford Bronco F-Series Twin 61mm Performance Throttle Body - $300

Brand new never installed BBK 3503 Twin 61mm performance throttle body. 50 state smog legal and C.A.R.B. approved ( D-245-13 ). For Ford Windsor small block v8 truck motors ( 5.0 , 5.8 , 302 , 351 ). Just get a set of gaskets and you're good to go. Sells for $350 or more. | http://www.bbkperformance...
by monkei
Fri Dec 21, 2012 1:11 pm
Forum: General Tech
Topic: No coil spark? Tried tons o stuff, what next?
Replies: 8
Views: 472

Re: No coil spark? Tried tons o stuff, what next?

unfortunately, the eec swap to a rebuilt unit didn't work. Might try replacing the TFI unit on the rebuilt distributor.
by monkei
Fri Dec 21, 2012 12:45 pm
Forum: General Tech
Topic: No coil spark? Tried tons o stuff, what next?
Replies: 8
Views: 472

Re: No coil spark? Tried tons o stuff, what next?

we have fuel pump so the power relay ain't it. we also have voltage at the coil terminals. the coil negative does not seem to be dropping low enough in voltage to cause spark (the test light just dims rather than flashes) checking PIP & SPOUT in AC (200v ACV range was the lowest the voltmeter would ...
by monkei
Fri Dec 14, 2012 12:07 pm
Forum: General Tech
Topic: No coil spark? Tried tons o stuff, what next?
Replies: 8
Views: 472

No coil spark? Tried tons o stuff, what next?

A lil' background: My buddy has a 90 5.0 bronco. It had been sitting for ~6mo and had its rear brakes done and was then drive to take care of smog. After smog, it died on the way back home and wouldn't start. We've been trying to troubleshoot the no start problem for days now to no avail. We get no ...
by monkei
Fri Sep 16, 2011 6:03 pm
Forum: General Tech
Topic: ABS Removal
Replies: 116
Views: 29626

Re: ABS Controller

Glad it helped!
by monkei
Mon Jun 27, 2011 1:34 pm
Forum: General Tech
Topic: Custom Stainless Steel Y-Pipe for Mass-Air - Any Interest?
Replies: 36
Views: 2667

Re: Custom Stainless Steel Y-Pipe for Mass-Air - Any Interest?

Hell yeah! I am totally ordering one of those! :!:
by monkei
Thu Jun 02, 2011 5:04 pm
Forum: General Tech
Topic: From superlift leafs to j40s....
Replies: 41
Views: 2972

Re: From superlift leafs to j40s....

D'oh. Too narrow, ah well. Know of a good place to see about getting some longer ones made? It doesn't look like ford made em longer than what came on the bronco for any of the heavier duty trucks.
by monkei
Thu May 26, 2011 1:00 pm
Forum: General Tech
Topic: From superlift leafs to j40s....
Replies: 41
Views: 2972

Re: From superlift leafs to j40s....

Just got 'em today, thanks mang!
by monkei
Fri May 20, 2011 6:07 pm
Forum: General Tech
Topic: From superlift leafs to j40s....
Replies: 41
Views: 2972

Re: From superlift leafs to j40s....

I usually get stuff shipped to my work, but if it's more convenient/cheaper, you can ship it to my pad instead. Zip for either address is 94566, thanks!
by monkei
Thu May 19, 2011 6:31 pm
Forum: General Tech
Topic: From superlift leafs to j40s....
Replies: 41
Views: 2972

Re: From superlift leafs to j40s....

I'll take 'em, the guy @ Camburg said they measure 3" from bushing to bushing. Hopefully having stuff that tight won't be an issue.
by monkei
Tue May 17, 2011 6:14 pm
Forum: General Tech
Topic: From superlift leafs to j40s....
Replies: 41
Views: 2972

Re: From superlift leafs to j40s....

I brought the other hanger home Sunday night so it's here when you find out. While I don't have a caliper here to get a precise measurement I do have a tape and these things are 2-5/16" clear now with the shackle in them. I'm sure they'd open up a little. 2 & 5/16" or 3 & 5/16"?? If it's the smalle...
by monkei
Mon May 16, 2011 9:41 pm
Forum: Go-Fast Tech
Topic: want to build a fsb for sand, need input
Replies: 23
Views: 2093

Re: want to build a fsb for sand, need input

I say TTB the Prospector! :mrgreen: (Bonus if it's got a 440!)
by monkei
Wed May 11, 2011 6:03 pm
Forum: Go-Fast Tech
Topic: Upgrading brake rotors to a larger size
Replies: 20
Views: 2047

Re: Upgrading brake rotors to a larger size

On those couple you've done, any issues with the mounts welded to the cast knuckle cracking at the weld?
by monkei
Wed May 11, 2011 5:55 pm
Forum: General Tech
Topic: From superlift leafs to j40s....
Replies: 41
Views: 2972

Re: From superlift leafs to j40s....

Sydude do you mind measuring the width of the Camburg shackle & bushing where it mounts to the shackle hanger? I THINK the camburg ones are 3" overall but can't say for sure. Just measured my Velvetride shackle and the metal portion is 2.75" wide at the hanger with a 3" width bushing, leaving 1/4" o...
by monkei
Tue May 10, 2011 11:50 am
Forum: General Tech
Topic: From superlift leafs to j40s....
Replies: 41
Views: 2972

Re: From superlift leafs to j40s....

shacklehang.JPG It is the inside measurement in red above on the shackle hanger. There seems to be a good amount of space on either side of the "velvet ride" shackle I'm running. I may be able to use one that is only 3" wide on the inside, but I'm not yet sure if the Camburg shackles are wider than...
by monkei
Mon May 09, 2011 9:32 pm
Forum: General Tech
Topic: Alcoas and 5/8 studs
Replies: 18
Views: 1722

Re: Alcoas and 5/8 studs

Are you guys enlarging the tapers by hand or indicating center for each hole on a mill? I plan to use first gen lighting 17x8 wheels (cast aluminum) with the 5/8 studs so it seems like this is something I'll be doing in the future.
by monkei
Mon May 09, 2011 6:45 pm
Forum: General Tech
Topic: From superlift leafs to j40s....
Replies: 41
Views: 2972

Re: From superlift leafs to j40s....

They measure 3.5" on the inside